# Bosch Dishwasher Error Codes: What E15, E24, E25 and Other Codes Mean

> Bosch dishwasher error codes explained from Bosch's own pages: what E15, E24, E25, E22 and other codes mean, which you can fix yourself, and when to call.

- URL: https://applianceinsider.org/blog/bosch-dishwasher-error-codes/
- Publisher: Appliance Insider (https://applianceinsider.org)
- Category: Troubleshooting & Error Codes; Appliance: Dishwashers; Brands: Bosch
- Published: 2026-10-22; Last updated: 2026-10-22; Author: Morgan Hale

Bosch dishwasher error codes tell you which system the dishwasher thinks has a problem, and the most common ones are drain and filter codes you can usually clear yourself. According to Bosch, **E24** means the dishwasher isn't draining because the drain filter is blocked, **E25** means the drain pump is blocked or its cover is loose, and **E22** means the filter itself is clogged. **E15** is different: it means the leak-protection system found water in the base, and Bosch says to turn off the water and call for service.

This guide lists what each code means according to Bosch's own support pages, splits them into the ones you can safely handle and the ones that need a technician, and walks through the drain fixes in detail. It's worth knowing before Thanksgiving, when a dishwasher can run several heavy loads in a day and a clogged filter shows up fast.

> **Note:**
> Codes and displays vary by model and age. Some newer Bosch models show four-digit codes (E6103 instead of E24, for example). If your code isn't listed here, Bosch asks you to have your model number ready and call Bosch Customer Support at 1-800-944-2904.

## How to clear a Bosch dishwasher error code

Bosch's reset steps are the same for most codes, once you've fixed the cause:

1. Turn the dishwasher off with its power button, or switch off its circuit breaker.
2. Wait about **one minute**. Bosch says the pause lets the electrical components discharge.
3. Turn the power back on.
4. Run a short test cycle with **no dishes** to confirm the code is gone.

For many electronic and component faults, Bosch's own advice is to **reset power at the breaker for 30 seconds**, then call Bosch Customer Support if the code isn't resolved. If a code keeps coming back, a reset is only hiding the problem.

> **Warning:**
> Turn off the dishwasher and its breaker before you remove the filter or pump cover, and expect some standing water underneath. Bosch warns that debris in the pump can be sharp. Don't open the control panel, kick plate or base, and don't try to tilt or drain the dishwasher yourself after an E15 code; turn off the water supply and call for service.

## Bosch dishwasher error code chart

Meanings below come from Bosch's US "Dishwasher Error Codes" page and its individual code guides, checked on October 22, 2026. Four-digit codes that Bosch lists with the same meaning are shown in parentheses.

| Code | What Bosch says it means | What to do |
| --- | --- | --- |
| E01 (E0100) | Heat pump motor circuit fault at the main control board | Reset breaker 30 seconds; call Bosch if it returns |
| E02, E03 (E0103, E0107) | Main control board relay fault | Reset breaker 30 seconds; call Bosch if it returns |
| E04 (E0105) | Faulty heater electronics found in the self-test | Call Bosch |
| E05 (E0106) | Wash arm diverter circuit fault in the main control board | Reset breaker 30 seconds; call Bosch if it returns |
| E06 (E8000) | Door sensor circuit fault | Reset breaker 30 seconds; call Bosch if it returns |
| E07 (E2130) | Zeolite (CrystalDry) fan motor defective | Reset breaker 30 seconds; call Bosch if it returns |
| E09, E20 (E2030, E6001) | Heat pump internal heater fault | Reset breaker 30 seconds; call Bosch if it returns |
| E10 (E2120) | Zeolite (CrystalDry) chamber heater fault | Reset breaker 30 seconds; call Bosch if it returns |
| E12 (E2060) | Limescale build-up in the heat pump | Descale the dishwasher; use softening salt if your model has a water softener |
| E14 (E3000) | Flow meter failure, or a problem with water flowing in | Call Bosch |
| E15 (E3100) | Water detected in the base; leak protection activated | Turn off the water supply and call Bosch |
| E16, E17 (E3300, E3400) | Water may not be able to enter the dishwasher | Check the inlet hose for kinks or damage |
| E18 (E3200) | Water level too low, or water not pumped correctly | Check the inlet hose and that the water supply is on |
| E19 (E6900) | Detergent dispenser solenoid circuit fault | Reset breaker 30 seconds; call Bosch if it returns |
| E21 (E6002) | Heat pump is blocked | Reset breaker 30 seconds; call Bosch if it returns |
| E22 (E9240) | Filter is blocked | Remove and clean the filter |
| E23 (E6101) | Drain pump blocked, clogged or faulty | Call Bosch |
| E24 (E6103) | Not draining properly because the drain filter is blocked | Clean the filter, check hoses, pump cover and disposal plug |
| E25 (E6102) | Drain pump blocked, or pump cover loose or missing | Reseat the pump cover and clear the pump |
| E27 (E9001) | House power supply to the unit is too low | Reset breaker 30 seconds; have an electrician check the voltage if it returns |
| E0110 | Failure causing electronics miscommunication | Call Bosch |
| E6160 | PowerControl lower spray arm reference position not found | Call Bosch |
| H01, h02 | Not an error: delay-start timer is set (1 hour, 2 hours) | Press + or – until h:00 shows to cancel |

The pattern is simple. Filter, drain and water-supply codes (E12, E16, E17, E18, E22, E24, E25) have steps you can do yourself. Control board, heater, sensor, flow meter, leak and drain pump motor codes are technician territory.

## E24: Bosch dishwasher not draining

E24 is the code most people search for, and it's the one a heavy holiday load is most likely to cause. Bosch says it means the dishwasher isn't draining properly because the drain filter is blocked, and you'll often see standing water in the bottom of the tub, a cycle that pauses or stops, or gurgling and humming noises.

Bosch lists three likely causes: a blocked drain hose, a filter that needs cleaning, or a brand-new garbage disposal whose knockout plug was never removed.

1. Turn off the dishwasher and its breaker, then lay towels in front of the door.
2. Remove the filter from the bottom of the tub (your owner's manual shows how on your model) and clean it as described under E22 below.
3. With the filter out, check that the **pump cover** underneath it isn't loose.
4. Check the hoses behind or under the dishwasher for kinks or damage. Bosch's E24 guide also says to make sure the siphon connection is sealed.
5. If the drain hose connects to a garbage disposal that was just installed, make sure the **knockout plug** has been removed from the disposal's dishwasher inlet. A plumber or the disposal's installer can do this if you're not comfortable working under the sink.
6. Reinstall the filter, restore power, and reset the dishwasher.

If the dishwasher still won't drain, our guide to [a dishwasher that won't drain](https://applianceinsider.org/blog/dishwasher-not-draining/) covers the air gap, the disposal connection and the drain hose loop in more detail.

## E25: drain pump blocked or pump cover loose

E25 is E24's close cousin. Bosch says it means the drain pump is blocked, or the drain pump cover is loose or missing.

1. Turn off the dishwasher and its breaker.
2. Remove the filter completely to reveal the drain pump cover at the bottom of the tub.
3. Check that the cover is seated. If it's loose, that alone can trigger E25.
4. To check the pump, Bosch says to pry the cover off with a spoon until it clicks, grip it and pull upward until you feel resistance, then pull it forward to remove it.
5. Remove any debris and standing water from the pump area with a sponge. Go slowly; Bosch warns some debris may be sharp.
6. Refit the pump cover until it's secure, reinstall the filter, and reset the dishwasher.

If E25 returns with the pump clear and the cover seated, or the code changes to **E23** (drain pump fault), stop there. Bosch says to call Bosch Customer Support for E23.

## E22: clogged dishwasher filter

Bosch says E22 means the filter is blocked. The filter catches food particles and needs regular cleaning, and Bosch says it sits at the bottom of the dishwasher.

1. Turn off the dishwasher and remove the bottom rack.
2. Remove the filter assembly following your owner's manual for your model.
3. Wash it under running water with **mild soap and a soft brush** until the mesh is clear.
4. Reinstall it fully, making sure it locks in place.

A clogged filter is also one of the most common reasons dishes come out gritty or cloudy. Our [dishwasher not cleaning dishes guide](https://applianceinsider.org/blog/dishwasher-not-cleaning-dishes-8-fixes-before-holiday-hosting/) covers the other causes, from spray arms to detergent.

## E15: water in the base (leak protection)

E15 is the code to take most seriously. Bosch says the safety switch has detected water in the base of the dishwasher and the leakage protection system has activated.

What Bosch tells owners to do is short: **turn off the water supply to the dishwasher and contact Bosch Customer Support at 1-800-944-2904.** The shutoff valve is usually under the kitchen sink.

Don't keep resetting it and running loads, and don't tip the dishwasher to empty the base. The water got there from a leak somewhere, and the leak needs to be found. While you wait for service, wipe up any water on the floor and check the cabinet under the sink for moisture.

## E16, E17 and E18: water isn't coming in

These codes all point to the water supply rather than the drain. Bosch says E16 and E17 mean water may not be able to enter the dishwasher, and E18 means the water level is too low or water isn't being pumped correctly.

1. Make sure the water supply valve (usually under the sink) is fully open.
2. Check the inlet hose for kinks or damage, especially if the dishwasher was recently pushed back into place.
3. For E18, Bosch specifies a water flow rate of **10 liters per minute** (about 2.6 gallons per minute). If other faucets in the house have weak pressure, fix that first.

If the supply is on and the hose is fine, Bosch says to contact Bosch Customer Support. E14, a flow meter fault, also involves the fill system but goes straight to a service call.

## Bosch dishwasher beeping

Bosch says beeping patterns often accompany a code:

- **Beeps but won't start:** usually the door isn't latched. Close it firmly; a broken latch may need replacing.
- **Beeps 3 times:** usually water pooling at the base. Clean the drain filter, check the hoses for clogs or leaks, and clean the door seal.
- **Beeps 5 times:** often water at the base triggering the sensor, which may need a technician.
- **Beeps with no display:** turn off the breaker for about **10 minutes**, then try again. If that doesn't help, Bosch says the control board may need replacing.

## When to stop and call a technician

Call Bosch Customer Support or a qualified appliance technician when:

- you see **E15**, any water on the floor, or a code with no DIY step (E04, E14, E23, E0110, E6160);
- a control board, heater, sensor or CrystalDry code comes back after a 30-second breaker reset;
- **E27** keeps returning, which Bosch says calls for an electrician to check the incoming voltage;
- drain codes return even with a clean filter, a seated pump cover and clear hoses.

If your dishwasher is out of warranty and the repair quote is high, our [repair or replace guide](https://applianceinsider.org/blog/repair-or-replace-appliance-guide/) walks through the decision. Shopping for a replacement? Our [Bosch 500 vs. 800 Series comparison](https://applianceinsider.org/blog/bosch-500-vs-800-series-dishwasher/) explains how the lines differ.

## How to prevent Bosch dishwasher error codes

Most of the codes owners can fix come from the filter and drain, so a little routine care prevents most of them:

- **Clean the filter regularly**, and more often during heavy-use weeks like the holidays. It's on our [appliance maintenance calendar](https://applianceinsider.org/maintenance-calendar/).
- **Scrape food scraps** into the trash before loading so less debris reaches the filter and pump.
- **Descale** if you live in a hard water area, and keep the softening salt topped up if your model has a water softener. Bosch says this helps prevent E12.
- **Leave the water valve fully open** and keep the inlet hose straight when sliding the dishwasher back in.

For other brands' codes, see our [error code hub](https://applianceinsider.org/error-codes/).

## Step-by-step summary

Estimated time: 30m

Tools: Spoon, Soft brush, Sponge

Supplies: Towels, Mild dish soap

1. **Write down the exact code.** Note the code exactly as the display shows it, such as E24 or E6103, and look it up in the table. H01 or h02 is a delay-start timer, not a fault.
2. **Turn off power before reaching inside.** Switch the dishwasher off and turn off its circuit breaker before you remove the filter or pump cover. For E15, also turn off the water supply and call Bosch.
3. **Clean the filter.** Remove the filter from the bottom of the tub and wash it under running water with mild soap and a soft brush, then reinstall it.
4. **Check the drain pump cover and hoses.** With the filter out, make sure the pump cover underneath is seated and clear any debris and standing water with a sponge. Check that the drain and inlet hoses aren't kinked and that the water supply is on.
5. **Reset the dishwasher.** Turn the power off at the button or the breaker, wait about one minute, turn it back on, and run a short empty test cycle.
6. **Call for service if the code returns.** If the code comes back after the checks and a reset, or it is one Bosch says to call about, contact Bosch Customer Support or a qualified technician.

## Frequently asked questions

**Q: How do I reset a Bosch dishwasher error code?**

A: Bosch says to turn the dishwasher off with the power button or at the circuit breaker, wait about one minute, turn it back on, and run a short test cycle with no dishes. If the code returns, the underlying problem is still there.

**Q: What does E15 mean on a Bosch dishwasher?**

A: E15 means the safety switch has detected water in the base of the dishwasher and the leakage protection system has activated. Bosch says to turn off the water supply and contact Bosch Customer Support at 1-800-944-2904.

**Q: What is the difference between E24 and E25 on a Bosch dishwasher?**

A: Bosch says E24 means the dishwasher is not draining properly because the drain filter is blocked, while E25 means the drain pump is blocked or the drain pump cover is loose or missing. Both start with removing the filter and checking the pump cover underneath it.

**Q: What does H01 mean on a Bosch dishwasher?**

A: H01 is not an error. Bosch says it shows that the delay-start timer has been set, with H01 meaning a one-hour delay and h02 a two-hour delay. Press the plus or minus button until h:00 shows to cancel it.

**Q: Why is my Bosch dishwasher beeping 3 times?**

A: Bosch says three beeps usually indicate water pooling at the base of the dishwasher. It suggests checking and cleaning the drain filter, inspecting the hoses for clogs or leaks, and cleaning the door seal.

**Q: Why does my Bosch dishwasher show a four-digit code like E6103?**

A: Some Bosch models display longer codes. Bosch's code list pairs many of them with the familiar two-digit codes, for example E6103 with E24, E6102 with E25, E3100 with E15 and E9240 with E22.

## When to call a pro

For repairs beyond basic checks in Maryland, Virginia, Washington D.C., West Virginia, Pennsylvania, Delaware, North Carolina, South Carolina, and Georgia, Appliance Insider recommends [VIA Appliance](https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-bosch-dishwasher-error-codes) (book online: https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-bosch-dishwasher-error-codes#book). VIA Appliance is a featured repair partner of Appliance Insider.

## Sources

- [Bosch: Dishwasher Error Codes](https://www.bosch-home.com/us/owner-support/dishwashers/error-codes)
- [Bosch: E15 Bosch Dishwasher Error Code](https://www.bosch-home.com/us/owner-support/get-support/support-selfhelp-dishwasher-error-e15)
- [Bosch: Bosch Dishwasher Error Code E24](https://www.bosch-home.com/us/owner-support/get-support/support-selfhelp-dishwasher-error-e24)
- [Bosch: E25 Bosch Dishwasher Error Code](https://www.bosch-home.com/us/owner-support/get-support/support-selfhelp-dishwasher-error-e25)
- [Bosch: E22 Bosch Dishwasher Error Code](https://www.bosch-home.com/us/owner-support/get-support/support-selfhelp-dishwasher-error-e22)
- [Bosch: E18 Bosch Dishwasher Error Code](https://www.bosch-home.com/us/owner-support/get-support/support-selfhelp-dishwasher-error-e18)
