# Gas Stove Burner Clicking but Won't Light? 8 Fixes to Try First

> Gas stove burner clicking but won't light? Wet or clogged ports, a misplaced cap or a loose igniter are the usual causes. GE and Whirlpool fixes, step by step.

- URL: https://applianceinsider.org/blog/gas-stove-burner-clicking-but-wont-light/
- Publisher: Appliance Insider (https://applianceinsider.org)
- Category: Troubleshooting & Error Codes; Appliance: Cooktops; Brands: GE, Whirlpool
- Published: 2026-10-26; Last updated: 2026-10-26; Author: Morgan Hale

A gas stove burner clicking but won't light almost always has a wet or clogged burner, a burner cap that isn't sitting right, or an igniter electrode that isn't seated flush. GE Appliances says most ignition problems happen right after the cooktop is cleaned or something boils over, and that a wet burner will keep clicking until its ports are clear and dry. Dry the parts, clear the ports with a pin, reseat the cap and electrode, and most burners light again within a few tries.

The steps below come from GE's and Whirlpool's own troubleshooting pages and apply to most gas ranges and cooktops with electronic (spark) ignition. Burner designs vary by brand and model (sealed, open and other burner types come apart differently), so check your owner's manual for your model's exact cleaning steps.

> **Warning:**
> **If you smell gas, stop.** Don't try to light a burner, don't switch lights or appliances on or off, and don't use a phone inside. Leave the home, leaving doors open if you can, then call 911 and your gas utility's emergency line from a safe place, as gas utilities such as Washington Gas advise. Before cleaning or handling burner parts, turn every burner off, let the cooktop cool, and disconnect power to the range. Never repair gas lines, valves or regulators yourself.

## Quick diagnosis: what is your burner doing?

| What you notice | Most likely cause | What to check |
| --- | --- | --- |
| Clicks but won't light, right after cleaning or a spill | Moisture in the ignition and flame ports | Fix 2: dry the burner |
| Clicks, lights unevenly or not at all, food residue visible | Clogged burner ports | Fix 3: clear the ports |
| One burner clicks but won't light after reassembly | Cap or head on the wrong burner or not flat | Fix 4: match and seat the parts |
| Spark is weak or electrode sits above the cooktop | Dirty or raised electrode | Fix 5: wipe and seat the electrode |
| No burner works and the display says Locked | Control Lockout (some models) | Fix 6: unlock the cooktop |
| No burner lights on a new install or after the gas was off | Gas supply off or air in the line | Fix 7: check the gas supply |
| Burner is lit but keeps re-sparking | Downdraft vent pulling the flame away | Fix 8: lower the vent speed |
| Clicks with every knob off | Moisture in the ignition switches | See the section on clicking when off |
| No clicking at all | No power to the range, or a failed part | Breaker, lockout, then service |

## Fix 1: Turn the knob all the way to Lite or Ignite

Whirlpool notes that the igniter only sparks when the knob is lined up with the Ignite position. GE's first step is the same: turn the burner to Lite. If you hear clicking, move on to the burner checks below. If you hear nothing, check the circuit breaker that powers the range; if the breaker is fine, GE says to schedule service.

If gas flows but the burner still doesn't light after GE's 10 to 12 clicks, turn the knob off before you go any further.

## Fix 2: Dry a wet burner (the most common cause)

GE says most ignition problems start when the burner head gets clogged or wet after cleaning or a spillover. Water trapped in the burner head's ignition port and flame ports keeps the gas from catching, so the igniter just keeps clicking.

1. Turn every burner off, let the cooktop cool, and disconnect power to the range or cooktop.
2. Remove the grate, burner cap and burner head.
3. Shake out any excess water.
4. Let the heads and caps dry thoroughly. GE says you can air dry them or set them in a warm oven for 30 minutes.
5. Put the heads and caps back in their correct positions, restore power and try the burner again.

Whirlpool adds that you can speed up drying by blowing cool air from a hair dryer over the area. This is the fix to try first if the stove was fine until you wiped it down or a pot boiled over, which is exactly what happens during big holiday cooking days.

## Fix 3: Clear clogged burner ports with a pin

Grease and cooked-on spills can block the small ports around the burner head and the ignition port next to the electrode. GE says to poke through the holes with a needle or paper clip. Whirlpool's cleaning instructions are more specific:

1. Make sure all controls are off and the cooktop is cool.
2. Remove the burner cap and base, and clean them with a non-abrasive plastic scrub pad and a mildly abrasive cleaner.
3. Clean the gas tube opening under the base, and gently clean the igniter with a damp cloth.
4. Clear clogged ports with a straight pin, needle or small-gauge wire.

> **Important:**
> Never use a wooden toothpick. Whirlpool warns it can break off and block gas flow. Don't enlarge or distort the ports either, and if a burner needs adjustment, have a trained technician do it.

Whirlpool also says not to use oven cleaner, bleach or rust remover on burners, not to wash burner caps in the dishwasher, and not to clean them in the oven during a self-clean cycle. If you're also getting the oven ready for the holidays, our [oven cleaning guide](https://applianceinsider.org/blog/how-to-clean-your-oven-before-the-holidays/) covers that part separately.

## Fix 4: Put the right cap on the right burner

Many cooktops have burners of different sizes, and the heads and caps aren't interchangeable. GE says each burner head must sit in its correct position and each cap must match its head; a correctly fitted cap lies flat and fits securely. Whirlpool says the cap should sit flush with the base with very little side-to-side movement, and any alignment pins should line up with the cap.

If a burner still doesn't light after you dry and clean it, Whirlpool's next check is cap alignment and whether the correct cap is on the correct base.

## Fix 5: Wipe the electrode and press it flush

The igniter electrode is the small white ceramic post next to the burner head. GE gives two checks, with all burners off and cool:

1. Remove the grate, cap and head so you can see the electrode.
2. Wipe the electrode tip with a clean, dry paper towel, even if it looks clean.
3. If the electrode isn't sitting flush with the cooktop, press down on it with your thumb and index finger using a clockwise twisting motion until it sits flush.
4. Reassemble the burner and try it again.

## Fix 6: Turn off Control Lockout (some models)

If no burner will light after a power outage or after the range was unplugged, check the display. Whirlpool says that on models with a Control Lockout feature, the surface burners start out locked when power first returns, and **Locked** appears on the display. The knobs can't turn the burners on until it's disengaged.

Whirlpool's typical unlock: touch the lock key for 3 seconds until the indicator light turns off and one long tone sounds. Controls vary, so confirm the steps in your owner's manual.

## Fix 7: Check the gas supply (new installs and first use)

If **every** burner fails to light, Whirlpool says to check that the appliance is connected to the gas supply and the shutoff valve is turned on. If the cooktop is new and the burners have never been used, Whirlpool says to turn on one burner knob to release air from the gas lines.

If the range isn't connected to gas, or you have any doubt about the connection, have a qualified gas technician handle it. Don't disconnect, tighten or modify gas fittings yourself. Our [gas vs. electric vs. induction range guide](https://applianceinsider.org/blog/gas-vs-electric-vs-induction-range-buying-guide/) covers what installation involves if you're weighing a replacement.

## Fix 8: Lower a downdraft vent that keeps re-sparking the burner

Whirlpool says a downdraft vent system can affect flame stability. On cooktops with flame-sensing ignition, it can pull the flame away from the spark igniter, so the igniter keeps sparking to relight a burner that is already lit. The fix is to lower the downdraft blower speed or turn that burner's flame up.

## Why does my gas stove click when the burners are off?

Clicking with every knob off is a different problem from a burner that won't light. Whirlpool says it usually means moisture got into the ignition switches from cleaning or a spill. Give it time to dry. To speed it up, pull the knobs off and blow cool air from a hair dryer onto the knob shafts.

## When it's probably not a DIY fix

Call for service if:

- The igniters don't click at all and the breaker, lockout and power check out. GE says this needs service.
- The igniter sparks properly but the burner still won't light after cleaning, drying and reseating. GE says to schedule service at that point.
- A burner needs flame adjustment, or the ports look damaged or enlarged (Whirlpool says to contact a trained repair specialist).
- You smell gas, hear hissing, or the range needs any work on the gas line, valve or regulator.

## How to keep burners lighting reliably

- Wipe spills once the cooktop has cooled, and keep water and cleaner out of the burner ports and away from the knobs.
- After washing burner heads and caps, dry them completely before putting them back.
- Put each cap back on its own burner, flat and centered.
- Add a quick burner check to your routine on the [maintenance calendar](https://applianceinsider.org/maintenance-calendar/), especially before big cooking days like Thanksgiving.

For oven-side problems on the same range, see our [GE and Whirlpool oven error codes guide](https://applianceinsider.org/blog/ge-whirlpool-oven-error-codes/), and browse more fixes in the [error codes hub](https://applianceinsider.org/error-codes/).

## Step-by-step summary

Estimated time: 45m

Tools: Straight pin or sewing needle, Hair dryer (cool setting)

Supplies: Clean, dry paper towels, Non-abrasive plastic scrub pad, Mild cleaner

1. **Check the knob position and the display.** Turn the knob fully to Lite or Ignite, since the igniter only sparks there. If the display shows Locked, turn off Control Lockout per your manual; on many Whirlpool models you touch the lock key for 3 seconds.
2. **Turn everything off and let it cool.** Turn every burner off, let the cooktop cool, and disconnect power to the range or cooktop before you take the burner apart.
3. **Dry wet burner parts.** If the stove was just cleaned or something boiled over, shake water out of the burner heads and caps and let them dry fully, either by air drying or in a warm oven for 30 minutes as GE suggests.
4. **Clear clogged ports.** Poke food or residue out of the burner ports with a straight pin or needle. Never use a wooden toothpick, and don't enlarge or distort the holes.
5. **Wipe and seat the electrode.** Wipe the white ceramic electrode with a dry paper towel. If it sits higher than the cooktop, press it down with a clockwise twist until it is flush.
6. **Reassemble with matching parts.** Put each burner head back in its own spot and the matching cap on top. A correctly fitted cap lies flat and barely moves side to side.
7. **Restore power and test.** Restore power and light the burner. GE says it can take 10 to 12 clicks. If the igniter doesn't click at all or the burner still won't light, schedule service.

## Frequently asked questions

**Q: Why does my gas burner keep clicking after I cleaned the stove?**

A: Water left in the burner head's ignition port and flame ports is the most common reason. GE says a wet burner will click continuously and won't light until the ports are clear and the burner dries out, so dry the heads and caps fully before using them.

**Q: How many clicks does it take for a gas burner to light?**

A: GE says it can take up to 10 or 12 clicks to ignite a burner, especially right after the parts were cleaned and reassembled. If it never lights, turn the knob off and check the burner for moisture, clogged ports and a misaligned cap.

**Q: Why does my gas stove click when all the burners are off?**

A: Whirlpool says clicking with every knob turned off usually means moisture got into the ignition switches during cleaning or from a spill. Let it dry; you can speed it up by removing the knobs and blowing cool air from a hair dryer onto the knob shafts.

**Q: Can I use a toothpick to clean gas burner holes?**

A: No. Whirlpool warns that a wooden toothpick can break off in the port and block gas flow. Use a straight pin, needle or small-gauge wire, and don't enlarge or distort the holes.

**Q: Why won't my gas stove click at all?**

A: If no burner clicks, check the circuit breaker for the range and look for a Locked message, since Whirlpool's Control Lockout blocks the burners after a power loss on some models. If power is fine and the igniters still don't click, GE says the range needs service.

## When to call a pro

For repairs beyond basic checks in Maryland, Virginia, Washington D.C., West Virginia, Pennsylvania, Delaware, North Carolina, South Carolina, and Georgia, Appliance Insider recommends [VIA Appliance](https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-gas-stove-burner-clicking-but-wont-light) (book online: https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-gas-stove-burner-clicking-but-wont-light#book). VIA Appliance is a featured repair partner of Appliance Insider.

## Sources

- [GE Appliances: Gas Range & Cooktop - Common Causes for Slow Ignition, No Ignition or Clicking on Surface Burners](https://products.geappliances.com/appliance/gea-support-search-content?contentId=17827)
- [GE Appliances: Gas Range & Cooktop - Burners Won't Light](https://products.geappliances.com/appliance/gea-support-search-content?contentId=17361)
- [Whirlpool: The Surface Burners are Making a Clicking Noise but Failing to Ignite on Your Whirlpool Cooktop](https://producthelp.whirlpool.com/Cooking/Cooktops/Product_Info/Cooktop_Product_Assistance/Gas_Burners_are_Clicking_but_Not_Lighting)
- [Whirlpool: Best Cleaning Method for Whirlpool Gas Cooktop Burners and Ports](https://producthelp.whirlpool.com/Cooking/Cooktops/Product_Info/Cooktop_Cleaning_and_Care/Cleaning_Gas_Cooktop_Burners_and_Ports)
- [Washington Gas: Natural Gas Safety (what to do if you smell gas)](https://www.washingtongas.com/safety)
