# Oven Error Codes: What GE F2, F3, F9 and Whirlpool F3 E0, F2 E1 and F9 E0 Mean (and When a Reset Fixes It)

> Oven error codes explained from GE and Whirlpool's own support pages: what F2, F3, F9, F3 E0, F2 E1 and F9 E0 mean, how a breaker reset works, and when to call.

- URL: https://applianceinsider.org/blog/ge-whirlpool-oven-error-codes/
- Publisher: Appliance Insider (https://applianceinsider.org)
- Category: Troubleshooting & Error Codes; Appliance: Ranges & Ovens; Brands: GE, Whirlpool
- Published: 2026-10-20; Last updated: 2026-10-20; Author: Morgan Hale

Oven error codes are the oven's way of telling you which part of the system it thinks has failed, and some of them clear with a simple breaker reset. On GE ovens, **F2** means the oven got hotter than a preset limit, **F3** usually means the temperature sensor needs replacing, and **F9** points to the door lock circuit. On Whirlpool ovens, **F3 E0** points to the temperature sensor, control, or wiring, **F2 E1** to the keypad or control, and **F9 E0** to miswired power or a power glitch.

This guide covers what each code means according to GE Appliances' and Whirlpool's own support pages, what you can safely try first, and when to stop and book service. It matters most in the weeks before Thanksgiving, when ovens work hardest and a lot of people run self-clean beforehand.

> **Note:**
> Codes vary by model and age. GE says it can't list every fault code for past and present models, and Whirlpool says its codes can show as F# E# or E# F#. If your code isn't listed here, check your owner's manual for your exact model number.

## How to clear an oven error code

Both brands use the same first step: reset the power.

1. Turn off the circuit breaker (or remove the fuse) that supplies the range or wall oven. Whirlpool's steps refer to breaker(s), so turn off every breaker or fuse that feeds the oven.
2. Leave it off for **one minute** (Whirlpool) or **a minute or two** (GE).
3. Turn the power back on. On Whirlpool ovens, don't press any keys for the first 10 seconds, because Whirlpool says pressing keys during that power-up delay can itself trigger F9.
4. Watch the display for one minute to make sure the code doesn't come back, then test the oven.

If the code returns, the reset didn't fix the cause. GE recommends leaving the range or wall oven off at the breaker until it has been serviced.

> **Warning:**
> Don't open the oven's back panel, control panel, or door-lock assembly, and never try to force a locked door open or bypass the door lock. Those parts carry line voltage and the lock protects you from a very hot oven. On gas ranges, if you smell gas, leave the house and call your gas utility from outside.

## GE oven error codes

These meanings come from GE Appliances' "Oven Error, Fault or Function Codes" page for ranges and wall ovens with electronic controls. GE says a trained technician should diagnose and correct a fault code.

| Code | What GE says it usually means | What to check |
| --- | --- | --- |
| F0, F1, F6, F7 | A problem with the keypanel; many times the keypanel needs replacing | Breaker reset; if it returns, schedule service |
| F2 or F20 | Oven temperature exceeded a preset threshold for an unknown reason | Breaker reset; stop using the oven if it returns |
| F3, F4 | The oven sensor needs replacing | Breaker reset; service if it returns |
| F5, F8, FF | The electronic control needs replacing | Service |
| F9, FC | A component failed somewhere in the door lock circuit | Let a self-clean finish and cool; reset; service if it returns |
| FD | The probe or its receptacle may need replacing | Service |
| F350 | An issue with the upper cooling fan circuit, or an obstruction in the fan | Service |
| F96, F97, F7X | An internal component needs replacing | Service |
| Bad Line | Power is reaching the unit, but it hasn't been wired correctly | Call an installer or electrician |
| Unlock Door, LOC Door | The door won't unlock after self-clean, or LOC Door flashes when self-clean wasn't selected | See GE's reset articles; don't force the door |
| LOC | Child lockout is on | Turn lockout off per your manual |
| ERR | An invalid entry when setting the controls | Re-enter the setting |
| OFF | The oven is too hot to start self-clean, or still cooling after self-clean | Let it cool longer and try again |
| ⊃ (backwards C) | Sabbath mode is on | Exit Sabbath mode per your manual |

## Whirlpool oven error codes

Whirlpool lists its cooking codes across a general error-code page and separate pages for individual range codes. The meanings below come from those pages.

| Code | What Whirlpool says it means | What to check |
| --- | --- | --- |
| F3 E0 | A possible problem with the oven temperature sensor, the control, or the wiring | Breaker reset for one minute; service if it returns |
| F2 E1 | A possible problem with the user interface or keypad, the control, or the wiring | Check that the grates are level, then reset the power |
| F9 or F9 E0 | The home's outlet or the connection to the appliance may be miswired | Reset the power; call an electrician if recently installed |
| C | The display is set to Celsius | Switch back to Fahrenheit per your manual |
| CAL | The oven calibration feature | See your manual |
| LOC, Lock, Locked | Control lock is on | Turn control lock off per your manual |
| SAB, Sab, 5AB, 5A6 | Sabbath mode is on | Exit Sabbath mode per your manual |
| PF | There has been a power failure | Press Cancel and reset the clock if needed |
| Blank clock | Some models can hide the time of day | Press and hold Clock Set/Start for about five seconds |

## GE F2: the oven got too hot

GE describes F2 (or F20) as the oven temperature exceeding a preset threshold "for an unknown reason." That makes it one of the codes to take most seriously. Try one breaker reset. If F2 comes back, leave the oven off at the breaker and have it checked rather than running it again, especially before a long holiday roast. If your oven is also failing to heat at all, our guide to [an electric oven that won't heat](https://applianceinsider.org/blog/electric-oven-not-heating-7-checks-before-you-call-a-technician/) covers the checks you can do safely before calling a technician.

## GE F3 and Whirlpool F3 E0: the temperature sensor

Both brands tie their F3 codes to temperature sensing. GE says F3 (and F4) usually means the oven sensor needs replacing. Whirlpool says F3 E0 means a possible problem with the oven temperature sensor, the control, or the wiring between them.

A breaker reset is the only step either brand gives homeowners for these codes. If the code clears and the oven heats normally, keep an eye on it. If it returns, the sensor, control, and wiring need testing by a technician. Neither brand publishes a homeowner resistance test for this code, so don't guess at one.

## GE F9 and Whirlpool F9 E0: same number, different problem

F9 means something different on each brand, which is why the brand matters when you search for it.

- **GE F9 (and FC):** a component has failed somewhere in the door lock circuit. If the door is still locked after self-clean, let the oven cool completely first. GE has separate reset articles for "Unlock Door" and a flashing "LOC Door" message.
- **Whirlpool F9 or F9 E0:** a power-supply code, not a door code. Whirlpool says the outlet or the appliance's electrical connection may be miswired, and if the oven was installed within about the last three months, a qualified electrician should verify the supply. It can also appear after power-line "noise" during an outage, or if keys were pressed during the 10-second power-up delay, in which case a clean breaker reset often clears it.

Planning a self-clean before the holiday? Run it at least a few days early so there's time to deal with a lock code. Our [oven cleaning guide](https://applianceinsider.org/blog/how-to-clean-your-oven-before-the-holidays/) covers when self-clean makes sense and the gentler alternatives.

## Whirlpool F2 E1: check the grates first

Whirlpool's first step for F2 E1 on ranges isn't electrical. With the range cool, rock each cooktop grate corner to corner and side to side. If a grate wobbles, it may be installed backwards, so try switching the grates. Then cycle the power at the breaker to reset the code. If F2 E1 comes back, Whirlpool says the problem may be the user interface or keypad, the control, or the wiring, and it needs service.

## When an oven error code needs a technician

Call for service when:

- The same code comes back after a breaker reset.
- The code points to a part replacement (keypanel, sensor, control, door lock) or to F2 overheating.
- The door won't unlock after the oven has fully cooled.
- The display shows **Bad Line** or Whirlpool **F9 E0** on a new installation, which calls for an electrician.
- You smell gas or see scorching, sparking, or melted wiring. Turn the power off at the breaker (and close the gas shutoff if you know where it is and can reach it safely), and for any gas smell, leave and call the gas utility.

You can look up other brands' codes on our [appliance error code hub](https://applianceinsider.org/error-codes/).

## Your Thanksgiving backup plan if the oven is down

If a code shows up close to the holiday and service can't come in time, you still have options:

- **Use the cooktop.** GE says it's okay to switch the breaker back on long enough to use the surface units, then turn the range off at the breaker again when you finish.
- **Spread out the oven dishes.** Sides and desserts that would normally share the oven can go to a countertop oven, a slow cooker, or a neighbor's oven.
- **Call as soon as a code repeats.** Don't wait to see whether it clears on its own the week of the holiday.

## How to prevent oven error codes

Error codes usually point to a failed part, so there's no way to prevent all of them, but a few habits help:

- Run self-clean well ahead of a big cooking day, never the night before.
- If you see GE's F350 code, remember that GE says an obstruction in the upper cooling fan can cause it, so don't block the oven's vents.
- Make sure cooktop grates are seated correctly after cleaning.
- After a power outage, wait 10 seconds before pressing any keys.

For a full list of seasonal tasks, see the [appliance maintenance calendar](https://applianceinsider.org/maintenance-calendar/).

## Step-by-step summary

Estimated time: 15m

1. **Write down the exact code.** Note the code exactly as shown, including both parts of a Whirlpool code such as F3 E0, and whether the oven was in self-clean or just losing power.
2. **Rule out non-fault displays.** Check whether the display is a feature rather than a fault, such as LOC (control lock), C (Celsius), SAB (Sabbath mode), PF (power failure), or OFF after self-clean.
3. **Do the quick checks.** On Whirlpool ranges showing F2 E1, make sure the cooktop grates sit level and aren't installed backwards. After a self-clean, let the oven cool fully before trying again.
4. **Reset the power at the breaker.** Turn off the circuit breaker or fuse for the range or wall oven for one to two minutes, turn it back on, and watch the display for a minute to see whether the code returns.
5. **Schedule service if the code comes back.** If the code returns, leave the oven off at the breaker until a technician checks it. GE says you can switch the breaker on long enough to use the surface units, then off again.

## Frequently asked questions

**Q: Can I reset an oven error code by turning off the breaker?**

A: Often, yes. GE says switching off the breaker or fuse for a minute or two sometimes clears an error code, and Whirlpool says to turn the breaker off for one minute, turn it back on, and watch for one minute to make sure the code doesn't return. If it comes back, the oven needs service.

**Q: What does F3 mean on a GE oven?**

A: On GE ranges and wall ovens, F3 usually means the oven temperature sensor needs to be replaced, according to GE Appliances. F4 has the same usual meaning.

**Q: What does F9 mean on a GE oven?**

A: On GE ovens, F9 usually means a component has failed somewhere in the door lock circuit, the same as FC. It often shows up around a self-clean cycle, and GE says a technician should diagnose it.

**Q: What does F9 E0 mean on a Whirlpool oven?**

A: Whirlpool says F9 or F9 E0 means the home's outlet or the electrical connection to the oven may be miswired. It can also appear after power-line noise during an outage, or if keys were pressed within 10 seconds of power coming back.

**Q: Can I still use my stovetop if the oven shows an error code?**

A: GE says it is okay to switch the breaker on and use the surface units, then turn the range off at the breaker again when you finish, until the oven is serviced. Gas cooktops have different rules, so check your manual, and if you smell gas, leave the house and call your gas utility.

**Q: Why does my oven say OFF after self-clean?**

A: On GE ovens, OFF means the oven is still too hot. If you try to start self-clean or bake shortly after a self-clean cycle ends, GE says to let the oven cool down longer and try again.

## When to call a pro

For repairs beyond basic checks in Maryland, Virginia, Washington D.C., West Virginia, Pennsylvania, Delaware, North Carolina, South Carolina, and Georgia, Appliance Insider recommends [VIA Appliance](https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-ge-whirlpool-oven-error-codes) (book online: https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-ge-whirlpool-oven-error-codes#book). VIA Appliance is a featured repair partner of Appliance Insider.

## Sources

- [GE Appliances: Range & Wall Oven - Oven Error, Fault or Function Codes](https://products.geappliances.com/appliance/gea-support-search-content?contentId=16238)
- [Whirlpool Product Help: Error Codes for Cooking Appliances](https://producthelp.whirlpool.com/Cooking/Wall_Ovens_and_Ranges/Product_Info/Oven_Product_Assistance/Error_Codes_for_Cooking_Appliances)
- [Whirlpool Product Help: F3 E0 - Error Code - Range](https://producthelp.whirlpool.com/Cooking/Wall_Ovens_and_Ranges/Ranges/Error_Codes/Starts_with_F/Starts_with_F3/F3_E0_-_Error_Code_-_Range)
- [Whirlpool Product Help: F2 E1 - Error Code - Range](https://producthelp.whirlpool.com/Cooking/Wall_Ovens_and_Ranges/Ranges/Error_Codes/Starts_with_F/Starts_with_F2/F2_E1_-_Error_Code_-_Range)
