# LG Refrigerator Error Codes: What Er FF, rF, FU, gF, dH and Other Codes Mean

> LG refrigerator error codes explained from LG's own support pages: what Er FF, rF, FU, gF, dH, CH and other codes mean, which you can fix, and when to call.

- URL: https://applianceinsider.org/blog/lg-refrigerator-error-codes/
- Publisher: Appliance Insider (https://applianceinsider.org)
- Category: Troubleshooting & Error Codes; Appliance: Refrigerators; Brands: LG
- Published: 2026-11-13; Last updated: 2026-11-13; Author: Morgan Hale

LG refrigerator error codes point to a specific part, and the one owners see most, **Er FF**, usually means the freezer fan is frozen in place by ice, which you can often fix with a full defrost. According to LG, **FU** means the freezer isn't getting cold enough and **gF** points to the water flow sensor, and both have home checks you can try first. Sensor, motor, communication and refrigerant-leak codes such as **rS**, **dH**, **It**, **CO**, **CH** and **CL** need a service call.

This guide lists the codes on LG USA Support's refrigerator error-code page, explains what to check for each, and walks through the ones you can act on. It's a good one to know before Thanksgiving, when a packed freezer and a door that gets opened every few minutes are exactly the conditions LG says lead to a frosted-over fan.

> **Note:**
> Codes vary by model. LG says codes can look different depending on the refrigerator and are usually shown with an **E**, **r** or **Er** prefix, so Er FF, E FF and F can all mean the same thing. Models without a digital display show faults as LED patterns instead, which your manual explains. If your code isn't listed here, check your user manual rather than guessing.

## How to see or clear an LG refrigerator error code

If you noticed a code but it's gone, for example after a power outage, LG says many models will show it again if you **press the Freezer Temperature and Express Frz buttons at the same time for at least 3 seconds.** Write the code down exactly before you do anything else.

There isn't one reset that clears every LG code. LG's steps depend on the code:

1. **FU and gF:** unplug the refrigerator, wait **60 seconds**, then plug it straight into a wall outlet, not a power strip or multi-plug adapter. LG says a full restart can take **up to 5 minutes**.
2. **Er FF, E FF, F and Er rF:** a restart won't free a fan that's frozen in place. LG's fix is a full defrost with the doors open for at least 24 hours (steps below).
3. **Everything else in the fault table:** LG says to request service.

> **Warning:**
> Unplug the refrigerator before you defrost it or reach behind it, and put towels down because melting ice can leave a lot of water on the floor. Don't use a hair dryer, heat gun or sharp tool to remove ice; LG warns heat can warp plastic parts or create a fire hazard. Never try to open or recharge the sealed refrigerant system yourself.

## Codes that aren't faults: Demo mode, Lo and HI

Three things on LG's list don't mean anything is broken:

- **Demo mode (display mode):** LG says this setting turns off all cooling in both compartments so a store display model doesn't waste energy. If your refrigerator lights up but never gets cold, check for it. To turn it off, LG says to open the refrigerator door, hold the **FRIDGE** button and press **Express FRZ** three times. On some models you instead hold **FRIDGE** and **Express FRZ** together for 3 seconds. A sound confirms it's off.
- **Lo:** the room temperature has dropped below **14°F (-10°C)**. LG says the refrigerator won't work well in that cold. If yours lives in a garage, see our guide to [keeping a refrigerator in a garage in winter](https://applianceinsider.org/blog/refrigerator-in-garage-in-winter/).
- **HI:** the room temperature has risen above **122°F (50°C)**, which is also outside what the refrigerator is built for.

## LG refrigerator error code chart

Meanings below come from LG USA Support's "Digital and Analog Error Codes" page and its Er FF and Er rF pages, checked on November 13, 2026.

| Code | What LG says it means | What to do |
| --- | --- | --- |
| Demo mode | Display mode: all cooling turned off | Turn it off with the FRIDGE and Express FRZ buttons (see above) |
| Lo | Room temperature below 14°F (-10°C) | Warm the room or move the refrigerator |
| HI | Room temperature above 122°F (50°C) | Cool the room or move the refrigerator |
| CF | Condenser fan fault | Request service |
| CO | Communication error between the main board and the display | Request service |
| FF, Er FF, E FF, F | Freezer fan isn't turning, usually because of ice or frost | Defrost for at least 24 hours; request service if it returns |
| rF, Er rF, E rF | Fan in the refrigerator compartment isn't working properly | Same defrost steps; request service if it returns |
| FS | Freezer temperature sensor fault | Request service |
| FU | Freezer hasn't dropped below about 38°F (3.5°C) 10 minutes after startup, or rose above it during operation | Restart from a direct outlet, then run LG's checks (see below) |
| IF | Ice maker fan fault | Request service |
| IS | Ice maker temperature sensor fault | Request service |
| It | Ice maker motor fault | Request service |
| rS | Refrigerator-side temperature sensor fault | Request service |
| dS | Defrost temperature sensor fault | Request service |
| rT | Room (ambient) temperature sensor fault | Request service |
| dH, FdH, dHF | Defrost sensor didn't warm by more than 9°F (5°C) within 80 minutes of defrost starting | Request service |
| SS | Water tank temperature sensor issue | Request service |
| gF | Water flow sensor fault | Restart, then check the water valve, hose and pressure (see below) |
| CH | Refrigerant leak on the high-pressure side | Request service; not a DIY repair |
| CL | Refrigerant leak on the low-pressure side | Request service; not a DIY repair |

The short version: Er FF, Er rF, FU and gF are the codes where LG gives you something to try at home. For the rest, LG's instruction is to request service. While you wait, keep the doors closed and move perishables to a cooler if temperatures start to climb.

## Er FF, E FF or F: LG freezer fan iced over

LG says **Er FF** (also shown as E FF, or just F) appears when **ice or frost around the freezer fan motor stops the fan from turning.** That usually happens when the freezer is packed too full or a door isn't fully closed, letting warm, humid air in. The related **Er rF** (or E rF) code means the fan in the refrigerator compartment isn't working properly, and LG gives it the same fix.

LG's defrost steps:

1. **Move the food** to another refrigerator or an insulated cooler.
2. **Put dry towels on the floor** around the refrigerator to catch melting ice.
3. **Unplug the refrigerator and leave both doors fully open for at least 24 hours** so the ice melts naturally. LG says it can take about a day in summer and up to three days in winter, depending on how much ice there is.
4. **Dry the inside** with a towel once all the ice is gone.
5. **Plug it back in** and allow **24 to 48 hours** for both compartments to reach normal temperatures.
6. **If the code comes back,** LG says to get further support or request a technician visit.

Plan around that timing. If you're hosting, the defrost and cool-down can take two to four days in total, so it's better to deal with an Er FF code well before the holiday than the night before. Once it's running again, don't overpack the freezer, and make sure nothing is keeping the door from sealing.

## FU: LG freezer not getting cold enough

LG says **FU** means the freezer hasn't dropped below about **38°F (3.5°C)** within 10 minutes of starting, or has risen above that during operation. LG's steps:

1. Unplug the refrigerator, wait 60 seconds, then plug it into a **direct wall outlet**, with no power strip or multi-plug adapter.
2. Check that the refrigerator is on, the compressor is running, and both compartments are set within normal ranges. LG's reference freezer setting is **0°F (-18°C)**.
3. Cut down how often and how long the doors stay open. LG notes every opening lets in warm, humid air.
4. Make sure food isn't **blocking the air vents** inside.
5. **Test the door gaskets with a sheet of paper.** Close the door on the paper and pull. It should resist if the seal is good.
6. If food in the door bins is affected by temperature swings, LG says the door insulation may have a problem.

If FU keeps coming back after those checks, request service. Our [refrigerator not cooling guide](https://applianceinsider.org/blog/refrigerator-not-cooling-causes-and-fixes/) covers the wider set of cooling problems, including dirty condenser coils.

## gF: LG refrigerator water flow sensor error

LG says **gF** indicates a malfunction of the water flow sensor, and that it can be caused by a **closed water valve, a kinked hose or incorrect water pressure.** LG's steps:

1. Unplug the refrigerator, wait 60 seconds and plug it into a direct wall outlet.
2. Wait for it to restart completely, which LG says can take up to 5 minutes.
3. Make sure the **water valve feeding the refrigerator is fully open** and water is reaching it through the hose.
4. Check that the **supply hose isn't kinked**, especially if the refrigerator was recently pulled out and pushed back.
5. Check your **water pressure**. LG says the flow sensor works within a set range, which your user manual lists.

If the code returns with good water supply, request service. If your ice maker has stopped too, our [ice maker not working guide](https://applianceinsider.org/blog/ice-maker-not-working-how-to-fix/) walks through the other common causes.

## When it's not a DIY fix

LG's list makes the line clear. Request service for:

- **Fan codes that come back after a full defrost** (FF, rF), or a **condenser fan** code (CF).
- **Sensor codes:** FS, IS, rS, dS, rT and SS.
- **Defrost heating code dH,** which LG says means the evaporator may be blocked by ice because the defrost system didn't warm up as expected.
- **Ice maker fan and motor codes:** IF and It.
- **Communication code CO** between the main board and the display.
- **Refrigerant leak codes CH and CL.** These involve the sealed system, which only a licensed technician should open.

If the refrigerator isn't holding a safe temperature while you wait for service, move perishables to a cooler with ice.

## How to prevent LG refrigerator error codes

Most of what triggers Er FF and FU comes down to airflow and door seals:

- **Don't overpack the freezer,** and keep food away from the air vents.
- **Make sure both doors close fully** every time. Check that a drawer, bin or tall item isn't holding a door open, and test the gaskets with the paper test once in a while.
- **Plug the refrigerator into its own wall outlet,** not a power strip.
- **Keep the room within range.** A garage that drops well below freezing or an unventilated space that gets very hot can set off Lo or HI.
- **Keep the condenser coils and water supply in good shape** with the routine tasks on our [maintenance calendar](https://applianceinsider.org/maintenance-calendar/) and in our [refrigerator maintenance checklist](https://applianceinsider.org/blog/refrigerator-maintenance-checklist/).

## Step-by-step summary

Estimated time: 30m

Tools: Flashlight, Sheet of paper

Supplies: Towels, Insulated cooler

1. **Write down the exact code.** Note the code exactly as the display shows it, including any E, r or Er prefix, and look it up in the table. If the code disappeared after a power outage, LG says many models will show it again if you press Freezer Temperature and Express Frz together for at least 3 seconds.
2. **Rule out codes that aren't faults.** Demo mode, Lo and HI are not refrigerator faults. Turn off Demo mode with the button combination in your manual, and move the refrigerator if the room is far too cold or too hot.
3. **Restart from a direct outlet.** For FU and gF, LG says to unplug the refrigerator, wait 60 seconds and plug it straight into a wall outlet, not a power strip. Give it up to 5 minutes to restart fully.
4. **Check the water supply for gF.** Make sure the water valve feeding the refrigerator is fully open, the supply hose isn't kinked, and household water pressure is normal.
5. **Defrost for Er FF, E FF or Er rF.** Move food to a cooler, put towels down, unplug the refrigerator and leave both doors fully open for at least 24 hours so the ice around the fan melts on its own. Don't use a hair dryer. Dry the inside, plug it back in and allow 24 to 48 hours to reach temperature.
6. **Request service if the code returns.** If a fan code comes back after defrosting, or you see a sensor, motor, communication or refrigerant-leak code such as CH or CL, unplug the refrigerator if it isn't cooling and request service from LG or a qualified technician.

## Frequently asked questions

**Q: How do I reset an LG refrigerator error code?**

A: For FU and gF, LG's steps are to unplug the refrigerator, wait 60 seconds and plug it into a direct wall outlet, then let it restart for up to 5 minutes. For Er FF, a reset alone won't help, because the fan is frozen in place; LG says to unplug it and defrost with the doors open for at least 24 hours. LG says most other codes need a service visit.

**Q: What does Er FF mean on an LG refrigerator?**

A: Er FF, also shown as E FF or F on some models, means the freezer fan motor isn't turning. LG says ice or frost around the motor is the usual cause, often from an overpacked freezer or a door that wasn't fully closed.

**Q: How long does it take to defrost an LG refrigerator for Er FF?**

A: LG says to leave the refrigerator unplugged with both doors fully open for at least 24 hours. It can take about a day in summer and up to three days in winter, depending on how much ice there is. After you plug it back in, allow 24 to 48 hours for it to reach normal temperatures.

**Q: Can I use a hair dryer to defrost my LG refrigerator?**

A: No. LG says not to use a hair dryer, because the heat could warp plastic parts inside the refrigerator or create a fire hazard. Leave the doors open and let the ice melt naturally.

**Q: What do CH and CL mean on an LG refrigerator?**

A: LG says CH indicates a refrigerant leak on the high-pressure side of the sealed system and CL a leak on the low-pressure side. These aren't DIY repairs. Request service, and don't try to open or recharge the sealed system yourself.

**Q: Why is my LG refrigerator showing Lo or HI?**

A: LG says these are warnings about the room, not refrigerator faults. Lo means the surrounding temperature has dropped below 14°F (-10°C) and HI means it has risen above 122°F (50°C), and the refrigerator won't work well in either condition.

## When to call a pro

For repairs beyond basic checks in Maryland, Virginia, Washington D.C., West Virginia, Pennsylvania, Delaware, North Carolina, South Carolina, and Georgia, Appliance Insider recommends [VIA Appliance](https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-lg-refrigerator-error-codes) (book online: https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-lg-refrigerator-error-codes#book). VIA Appliance is a featured repair partner of Appliance Insider.

## Sources

- [LG USA Support: [LG Refrigerator] Digital and Analog Error Codes](https://www.lg.com/us/support/help-library/lg-refrigerator-digital-and-analog-error-codes--20154835849096)
- [LG USA Support: If You See an Er FF, E FF, or F Error Code on Your LG Refrigerator](https://www.lg.com/us/support/help-library/if-you-see-an-er-ff-e-ff-or-f-error-code-on-your-lg-refrigerator--20155452969338)
- [LG USA Support: How to Fix ER FF and ER rF Error Codes on Your LG Refrigerator](https://www.lg.com/us/support/help-library/how-to-fix-er-ff-and-er-rf-error-codes-on-your-lg-refrigerator--20155433198922)
