# Samsung Dishwasher Error Codes: What 4C, 5C, LC, OC, HE and Other Codes Mean

> Samsung dishwasher error codes explained from Samsung's own support pages: what 4C, 5C, LC, OC, HE, 7E and other codes mean, what to check, and when to call.

- URL: https://applianceinsider.org/blog/samsung-dishwasher-error-codes/
- Publisher: Appliance Insider (https://applianceinsider.org)
- Category: Troubleshooting & Error Codes; Appliance: Dishwashers; Brands: Samsung
- Published: 2026-11-07; Last updated: 2026-11-07; Author: Morgan Hale

Samsung dishwasher error codes tell you which system has a problem, and the ones you'll see most often are water supply, drain and leak codes you can usually check yourself. According to Samsung, **4C** means the dishwasher isn't getting water at the pressure or temperature it needs, **5C** means it can't drain, **OC** means there's too much water inside, and **LC** means the leak sensor has detected moisture. Heater, pump, sensor and communication codes such as **HE**, **3C** and **CE** usually end in a service call if a simple restart doesn't clear them.

This guide lists every code on Samsung's US dishwasher error-code page, explains what to check for each, and walks through the four most common codes in detail. It's worth a look before Thanksgiving, when a dishwasher may run back-to-back loads of roasting pans and serving dishes and a clogged drain or blocked Waterwall reflector shows up fast.

> **Note:**
> Codes vary by model. Samsung says its list covers models with a digital display; models without one show errors as combinations of blinking lights, which Samsung explains in a separate guide. Some codes appear in two forms (5C or 5E, LC or LE). If your code isn't listed here, check your user manual rather than guessing.

## How to clear a Samsung dishwasher error code

Samsung's first rule is the important one: **don't try to reset or clear the code before you troubleshoot it.** Samsung says that if you clear a code without fixing the cause, the error may return or the dishwasher may be impaired.

Once you've worked through the checks for your code, Samsung's restart steps for several codes (1E on Rotary models and HC) are:

1. Switch the dishwasher's power **off at the circuit breaker for 30 seconds**, then back on.
2. Empty the dishwasher.
3. Fill the detergent drawer and start a **Normal** cycle.

For 7E, Samsung suggests a **two-minute** power cycle at the breaker. For codes like 3C, CE and PC, Samsung's step is simply to turn the dishwasher off and start the cycle again. If the same code returns, Samsung says to request service.

> **Warning:**
> Turn off the dishwasher at its circuit breaker before you clean the filter area or inspect hoses, and lay towels down in case water spills out. Samsung warns there may be sharp debris in the drain area. If you find an active leak, also turn off the water supply, usually at a valve under the sink. Don't open the dishwasher's electrical panels or try to repair the pump, heater or control board yourself.

## Samsung dishwasher error code chart

Meanings below come from Samsung US's "Samsung dishwasher is displaying an error code" page, checked on November 7, 2026.

| Code | What Samsung says it means | What to check |
| --- | --- | --- |
| 1E, IE | Waterwall models: clogged filter. Rotary models: high temperature heater error | Waterwall: clean the fine filter. Rotary: 30-second breaker reset, then a Normal cycle |
| 3C | Pump operation error | Turn off, restart the cycle; request service if it returns |
| 3E | Hot water supply is too hot | Make sure the water heater isn't set above 176°F |
| 4C, 4E | Water supply error: not getting water at the needed pressure or temperature | Water valve, supply line, pressure and temperature (see below) |
| 5C, SC, 5E, SE | Drain error: the dishwasher can't drain | Sink drain, disposal, drain hose and filter area (see below) |
| 6E, bE | Button error: the panel detects a stuck button | Turn off, touch every button; request service if it returns |
| 7E | Waterwall reflector can't move correctly | Clear obstructions and reseat the reflector (see below) |
| 9E | Low water level | Empty, add detergent, run a Normal cycle |
| AP | Not a fault: Access Point mode for Wi-Fi setup | Turn the dishwasher off and on if you aren't connecting it |
| CE | Communication error between the control panel and the dishwasher | Turn off, restart; request service if it continues |
| HC | High temperature heater error: too hot inside | 30-second breaker reset, empty, Normal cycle |
| HE | Heater error: temperature is being detected incorrectly | Empty, add detergent, run a Normal cycle |
| LC, LE | Leak sensor detects moisture | Power off, look for leaks, check detergent, let it dry (see below) |
| OC, 0C, oE | Over-level water: more water than there should be | Same drain checks as 5C |
| PC | Zone Wash function not operating correctly | Turn off, restart the cycle; request service if it returns |
| PE | Half load function error | Empty, add detergent, run a half load cycle |
| tE | Temperature sensor error | Empty, add detergent, run a Normal cycle |

The pattern is simple. Water supply, drain, leak and Waterwall codes (3E, 4C, 5C, 7E, LC, OC) mostly come from things you can check outside the machine. For heater, pump, sensor, button and communication codes (1E on Rotary models, 3C, 6E, CE, HC, HE, PC, PE, tE), Samsung's only home steps are a restart or a test cycle. If the code returns after that, switch off the breaker and request service.

## 4C: Samsung dishwasher not getting water

Samsung says **4C** (or 4E) means the dishwasher isn't getting water at the pressure or temperature it needs. Samsung's water supply requirements page lists what the dishwasher expects:

- **Water pressure:** 20 to 120 psi. Samsung says pressure below 20 psi can cause the water supply valve to fail and not shut off properly.
- **Hot water temperature:** 120 to 149°F (49 to 65°C) for the best cleaning and drying. Samsung cautions that water shouldn't exceed 149°F to avoid severe burns, and says inconsistent water temperature can trigger error codes.
- **Supply line:** sold separately; Samsung recommends a stainless steel line and says problems with the supply line can cause error codes.

What to check:

1. Make sure the water shutoff valve to the dishwasher (usually under the sink) is fully open.
2. Look for a kinked or pinched supply line, especially if the dishwasher was recently pushed back into place.
3. Run the kitchen faucet. If pressure is weak throughout the house, deal with that first.
4. If the house water lines could be frozen, let the area warm up before calling for service.

The related code **3E** is the opposite problem: Samsung says it means the incoming water is too hot, and to make sure the hot water supply isn't set above 176°F.

## 5C and OC: Samsung dishwasher not draining or overfilling

**5C** (also shown as SC, 5E or SE) means the dishwasher can't drain. **OC** (also 0C or oE) means there's more water inside than there should be. Samsung's not-draining guide covers both, and its first point is that the problem is often the sink drain, not the dishwasher.

1. **Check the sink drain and garbage disposal.** Make sure the disposal isn't clogged with food. If the disposal or dishwasher was recently installed, Samsung says to make sure the **disposal cap** (knockout plug) has been removed.
2. **Check the drain hose.** Samsung says the most common cause right after installation is the dishwasher sitting on its own drain hose and pinching it shut. The next most common is a hose with no **air gap** or **high loop** above its sink connection, which lets water flow back into the dishwasher. Straighten any kinks.
3. **Run water in the sink for about 30 seconds.** If the sink doesn't drain, Samsung says the problem is the home's plumbing; call a plumber.
4. **Clean the filter and drain area,** following your user manual for your model. Samsung stresses that removable parts must be reassembled correctly, because missing or misplaced parts can cause drain errors.
5. **Rule out frozen lines.** If the drain line could be frozen, open the cabinet door under the sink to let warm air in. Samsung notes frozen lines aren't covered by warranty service.

If it still won't drain, Samsung says to request service. Our [dishwasher not draining guide](https://applianceinsider.org/blog/dishwasher-not-draining/) explains the air gap and high loop in more detail.

## LC: leak sensor detects moisture

**LC** (or LE) is the code that surprises people, because Samsung says that when it appears, **the dishwasher turns itself on and won't turn off** while it tries to drain the water away. On Waterwall models, Samsung says LC can also mean the reflector is blocked, so check that too.

Samsung's steps for a leak code with no visible leak:

1. **Turn off the power at the circuit breaker** (or unplug it, if it plugs in), so it stops running while you troubleshoot.
2. **Look for a visible leak,** especially along the water supply hose and its connections at both ends. If you find one, turn off the water supply.
3. **Check the garbage disposal cap.** On a newly connected disposal, a cap left in place can push water where it reaches the leak sensor.
4. **Look for excess detergent.** Samsung says detergent is moist enough to trigger the sensor and dries more slowly than water. Don't overfill the dispenser, and don't add detergent outside it.
5. **Give it time to dry,** especially if the dishwasher was recently moved and water splashed under it.
6. **Restore power.** If LC is still there, request service.

If you can see water on the floor, Samsung's leak checklist adds a few more checks. Use dishwasher detergent only, never hand dish soap, which makes suds that can escape. Push a misaligned door seal back into its channel and clean it, and level the dishwasher, because a front that sits lower than the back lets water pool at the door. Samsung also says the cabinet opening should measure exactly 22 inches where the mounting screws are. If it's wider, the screws are overtightened and stretching the tub, so loosen them.

## 7E: Waterwall reflector error

Samsung says **7E** means the Waterwall reflector can't move, usually because something is blocking it or it wasn't reattached correctly. It's a common one on a holiday load with long-handled serving pieces.

1. Make sure nothing is blocking the reflector, such as a **pot handle, large knife or ladle**.
2. On a newly installed dishwasher, remove the **packing tape** along the top of the guide rail (take out the bottom rack to reach it).
3. Check the position. Samsung says the WaterWall logo should face forward and upward. If it doesn't, lift the vane off, turn it around, and reseat it on the gray shuttle on the rail.
4. Power cycle at the breaker for **two minutes** to clear the code.

Samsung says 7E very rarely needs service. It also warns that if a technician finds no defect, the visit may not be covered under warranty.

## When to stop and call a technician

Request service from Samsung or call a qualified appliance technician when:

- **3C** (pump), **CE** (communication), **HE**, **HC** or **tE** (heater and temperature) or **PC**/**PE** comes back after Samsung's restart steps;
- **LC** stays on after the base has had time to dry, or you find a leak anywhere along the drain hose other than its connection to the house;
- drain codes return with a clear sink drain, a straight hose with a high loop or air gap, and a clean filter area;
- a stuck-button code (**6E** or **bE**) returns, or a button doesn't respond.

If your dishwasher is out of warranty and the quote is high, our [repair or replace guide](https://applianceinsider.org/blog/repair-or-replace-appliance-guide/) can help you decide.

## How to prevent Samsung dishwasher error codes

Most of the codes owners can fix come from the drain path, the water supply and detergent, so routine care prevents most of them:

- **Clean the filter area** regularly, and more often during heavy-use weeks like Thanksgiving. It's on our [appliance maintenance calendar](https://applianceinsider.org/maintenance-calendar/).
- **Scrape food scraps** into the trash before loading, and keep tall utensils and pot handles clear of the Waterwall rail.
- **Use only dishwasher detergent** in the dispenser, and don't overfill it.
- **Keep the drain hose and supply line straight** when sliding the dishwasher back into place.

If dishes still come out dirty with no code, see our [dishwasher not cleaning dishes guide](https://applianceinsider.org/blog/dishwasher-not-cleaning-dishes-8-fixes-before-holiday-hosting/). For other brands, compare our [Bosch dishwasher error codes](https://applianceinsider.org/blog/bosch-dishwasher-error-codes/), the [Samsung washer error codes](https://applianceinsider.org/blog/samsung-washer-error-codes/) guide, or the full [error code hub](https://applianceinsider.org/error-codes/).

## Step-by-step summary

Estimated time: 30m

Tools: Flashlight, Soft brush

Supplies: Towels, Shallow pan

1. **Write down the exact code.** Note the code exactly as the display shows it, such as 4C, 5C or LC, and look it up in the table. Samsung says to troubleshoot before you try to reset or clear a code.
2. **Turn off power before reaching inside.** Switch off the dishwasher's circuit breaker before you clean the filter area or inspect hoses. For a leak code, also turn off the water supply if you find a visible leak.
3. **Check the water supply for 4C.** Make sure the water valve under the sink is fully open and the supply line is not kinked. Samsung specifies 20 to 120 psi and a hot water supply of 120 to 149°F.
4. **Check the drain path for 5C or OC.** Clear the garbage disposal, confirm the disposal knockout cap is removed on a new install, straighten the drain hose, and check that it has a high loop or air gap. Then clean the filter area and reassemble it as the manual shows.
5. **Dry out the base for LC.** With the power off, wipe up any water, look for leaks along the supply hose, check for excess detergent, and give the base time to dry before restoring power.
6. **Power cycle and run a Normal cycle.** For codes where Samsung lists it, switch the breaker off for 30 seconds, turn it back on, add detergent and run a Normal cycle on an empty dishwasher.
7. **Request service if the code returns.** If the code comes back after Samsung's steps, or it is a pump, heater, sensor or communication code that persists, request service from Samsung or a qualified technician.

## Frequently asked questions

**Q: How do I reset a Samsung dishwasher error code?**

A: Samsung says to troubleshoot the cause before you try to reset or clear a code, or the error may return. For several codes its steps are to switch the dishwasher off at the circuit breaker for 30 seconds, turn it back on, empty it, add detergent and run a Normal cycle.

**Q: What does 4C mean on a Samsung dishwasher?**

A: 4C, also shown as 4E, is a water supply error. Samsung says it means the dishwasher is not getting water at the pressure or temperature it needs, so check that the water valve is open, the supply line is not kinked, and pressure is between 20 and 120 psi.

**Q: Why does my Samsung dishwasher say LC and keep running?**

A: LC or LE means the leak sensor has detected moisture. Samsung says the dishwasher turns itself on and will not turn off while it tries to drain the water away, so switch it off at the breaker, look for a leak, check for excess detergent and let the base dry before restoring power.

**Q: What is the difference between 5C and OC on a Samsung dishwasher?**

A: 5C means the dishwasher cannot drain, while OC means there is more water in the dishwasher than there should be. Samsung sends both codes to the same drain checks: the sink drain and disposal, the drain hose, and the filter area.

**Q: What does 7E mean on a Samsung dishwasher?**

A: 7E is a Waterwall reflector error, which Samsung says means the reflector cannot move. Usually something like a pot handle or ladle is blocking it, or the reflector was reinstalled the wrong way, and Samsung says it rarely needs service.

**Q: What if my Samsung dishwasher has no display?**

A: Samsung says models without a digital display show errors as combinations of blinking lights instead of codes. Samsung has a separate blinking-lights guide, and your user manual lists the patterns for your model.

## When to call a pro

For repairs beyond basic checks in Maryland, Virginia, Washington D.C., West Virginia, Pennsylvania, Delaware, North Carolina, South Carolina, and Georgia, Appliance Insider recommends [VIA Appliance](https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-samsung-dishwasher-error-codes) (book online: https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-samsung-dishwasher-error-codes#book). VIA Appliance is a featured repair partner of Appliance Insider.

## Sources

- [Samsung US: Samsung dishwasher is displaying an error code](https://www.samsung.com/us/support/troubleshoot/TSG10004499/)
- [Samsung US: Samsung dishwasher water supply requirements](https://www.samsung.com/us/support/answer/ANS10004782/)
- [Samsung US: Samsung dishwasher is not draining](https://www.samsung.com/us/support/troubleshoot/TSG10004498/)
- [Samsung US: Samsung dishwasher is leaking or has a leakage error code](https://www.samsung.com/us/support/troubleshoot/TSG10010593/)
- [Samsung US: Waterwall reflector error code 7E on Samsung dishwasher](https://www.samsung.com/us/support/troubleshoot/TSG10007371/)
- [Samsung US: Lights are blinking on the Samsung dishwasher](https://www.samsung.com/us/support/troubleshoot/TSG10002410/)
