# Samsung Washer Error Codes: What 4C, 5C, UE, dC, LC and Other Codes Mean (and How to Fix Them)

> Samsung washer error codes explained from Samsung's own support pages: 4C, 5C, UE, Ub, dC, LC, SUd and more, with what to check and when to call service.

- URL: https://applianceinsider.org/blog/samsung-washer-error-codes/
- Publisher: Appliance Insider (https://applianceinsider.org)
- Category: Troubleshooting & Error Codes; Appliance: Washers; Brands: Samsung
- Published: 2026-10-28; Last updated: 2026-10-28; Author: Morgan Hale

Samsung washer error codes tell you why a cycle stopped, and the most common ones point to something you can check yourself. **4C** (or 4E, nF) means the washer isn't filling, **5C** (or 5E, SE, nd) means it can't drain, **UE**, **Ub** and **U6** mean the load is unbalanced, **dC** and **dE** usually mean the door isn't locked, and **LC** (or LE, 1E) means a leak or water level problem. This guide covers each Samsung washer error code using Samsung US's own support pages, for both front-load and top-load models.

> **Note:**
> Samsung makes many washer models, and some codes mean different things on different ones: **dC** is a door error on some models and an unbalanced load on others, **3E** is a voltage error on some and a motor error on others, and **BE2 (8E2)** is a jammed button on some and a MEMS sensor error on others. Check your owner's manual for your exact model before you act on those codes.

## How to clear a Samsung washer error code

Samsung's basic steps for any code without its own fix are:

1. Power off the washer for **2 to 3 minutes**.
2. Power it back on.
3. Restart the cycle.
4. If the error continues, request service.

For not-filling codes, Samsung says to unplug the washer or switch off its circuit breaker for **1 minute**, then restore power and run a cycle. A power-cycle only clears the message. If the cause is still there, such as a closed valve or a clogged pump filter, the code will come back, so do the checks for your code first.

> **Warning:**
> Unplug the washer before you open the pump filter panel or disconnect any hose, and turn the water valves off first when you remove the supply hoses. Samsung warns that after a hot cycle such as Pure Cycle or Sanitize, the water inside can be very hot, so wait about an hour before draining it.

## Samsung washer error code table

| Code (and variants) | What Samsung says it means | What to check |
| --- | --- | --- |
| **4C**, 1 4C, **nF**, **4E** | Not filling: water isn't entering correctly | Open both valves fully, connect hot to hot and cold to cold, unkink the hoses, check the drain hose depth, power-cycle for 1 minute, clean the inlet filters. |
| **4C2**, 4E2, CE, 14C2, nF1 | Hot/cold error: the cold supply is extremely hot | The supply hoses are swapped. Connect cold to the cold inlet and hot to the hot inlet (usually blue to blue, red to red). No service needed. |
| **5C**, **5E**, SE, SC, nd, 1 5C | No drain: water isn't draining, or drains too slowly | Check the drain hose installation, level the washer, and clean the pump filter on front loaders (details below). |
| **OE**, 0E, OC, 0C, 1 OC, 1 0C | Overflow: too much water in the washer | Follow Samsung's not-draining steps below; request service if it continues. |
| **1E**, **LE**, 1C, **LC**, LC1, 1 1C, 1 LC | Water level or leak error | Look for leaks, unkink the hoses, and run empty cycles if suds appear. |
| **dS**, d5, FL, LO, L0, **dE**, dE1, dE2, **dC**, dC1, dL, 1 dC, 1dC4, 1dC1 | Door not detected as closed and locked | Clear laundry from the door, make sure the latch is secure, and close the door firmly. |
| **ddC**, dC3 | AddWash door not closed and locked | Clear anything caught in the AddWash door and close it securely. |
| **UE**, **Ub**, U6, 1 Ub, 1U6 (dC on some models) | Unbalanced load: the cycle can't finish | Untangle and rearrange the laundry, close the door, and press Start. |
| **Ur** | Unbalanced load retry | Not a fault. The washer adds water, rebalances, and tries to spin again. |
| **SUd**, 5UD, Sd, 5d, SUdS, 5Ud5 | Excessive suds | The washer pauses to let suds settle, then continues. Use less detergent, and only HE detergent. |
| **SDC**, 5DC | Detergent drawer not fully closed | Push the drawer in until it clicks. |
| **E2**, bE2, 6E2 (BE2 or 8E2 on some models) | Jammed button | Power off, then press and wiggle every button on the panel. Request service if one is damaged or the code returns. |
| **9C1**, 9C2, **PF**, 2E, 9E1, 9E2, UC, 19C1, 19C2 (3E on some models) | Voltage error, or power failure mid-cycle | Plug the washer into its own circuit with no extension cord. PF also appears after an outage or a tripped breaker. |
| **Cb**, C6 | Calibration mode | Not a fault. Run calibration only with the drum empty; it takes 1 to 3 minutes. |
| **dn** | Downloading an update | Not a fault. Leave it powered on for about 15 minutes. Request service if it lasts more than 30 minutes. |

Samsung lists these codes as having **no specific DIY fix**. Do the 2-to-3-minute power-cycle, and request service if they return:

| Code (and variants) | What Samsung says it means |
| --- | --- |
| **3E**, 3C, E3, 1 3C | Motor error (3E is a voltage error on some models) |
| **AE**, AC, AE6, AC6 and other AE/AC variants | Communication error |
| **8E**, **BE**, 8C, BC and their variants | MEMS sensor error (vibration sensor on some models) |
| **tE**, tE1, tC | Temperature sensor error |
| **HE**, HC, HE1, Hr, 1 HC | Heater error |
| **PE**, PC | Clutch position error |
| PE1, PC1 | Clutch Hall signal error |
| bE, 6E | Motor speed sensor error |
| **SF**, 5F, IE and their variants | System error |
| Sr, 5r | System relay error |
| 9C6 / 9C7 / 9C8 | High-temperature circuit / hardware overcurrent / software overcurrent error |
| 7E | SilverCare error |

## 4C, 4E and nF: Samsung washer not filling

4C is one of the most common Samsung washer codes. Work through Samsung's checks in order:

1. **Check the hose connections.** Both the hot and cold supply hoses must be connected, hot to hot and cold to cold, with no bends or kinks. Samsung notes that if you leave the hot line disconnected, you'll get an error whenever the washer calls for hot water, which can happen even on cycles labeled Cold. Samsung also says not to use Flood Safe hoses with its washers.
2. **Open the water valves completely** and leave them open while the washer runs.
3. **Check the drain hose.** It should go no less than 6 inches and no more than 8 inches into the drain pipe, and it shouldn't be kinked.
4. **Power-cycle the washer.** Unplug it or switch off its breaker for 1 minute, then try a cycle.
5. **Clean the inlet filters.** Turn the water valves off, disconnect the hoses from the back of the washer, and look inside the connections. If debris has built up on the small filter screens, carefully remove them with needle-nose pliers, clean them, and reinstall. Reconnect the hoses and open the valves fully again.

If 4C still appears, Samsung says to request service. If the code is **4C2** instead, the hoses are swapped, and reversing them fixes it.

> **Important:**
> Don't remove the screw on the back of the washer that holds the drain hose against the cabinet. Samsung says that if it has been removed, you should put it and the holder back with any screw that fits, and that service is required if the holder is missing.

## 5C, 5E and nd: Samsung washer not draining

Samsung says an incorrectly installed drain hose is the most common reason for drain problems and that service is rarely required. Its steps:

1. **Turn the washer off and make sure it's level.** A washer that isn't level may not drain correctly.
2. **Inspect the drain hose.** Samsung's requirements: inserted no less than 6 and no more than 8 inches into the standpipe or sink; secured so it can't slip farther down; not forming an airtight seal; not kinked, bent, or damaged; at least 18 inches high (24 inches for a wash basin) and no higher than 96 inches (35 inches for a wash basin); and no drain hose extension kit.
3. **Clean the pump filter (front loaders only).** Top-load Samsung washers don't have a removable pump filter.
   - Open the access panel near the bottom front by pressing its top or center.
   - Put a towel and a container big enough for the water (an oil drain pan works) under the small rubber drain hose.
   - Twist the cap off the hose (it seals tightly) and let the water drain out.
   - Twist the pump filter counterclockwise to remove it. On some models it pushes in and twists, like a medicine bottle cap.
   - Brush it clean with a soft toothbrush, and check that the drain pump impeller inside the housing is clear.
   - Reinstall the filter clockwise until it's secure in the vertical position, cap the drain hose, clip it back in place, and close the panel.
4. **Turn the washer back on and start a cycle.** It should drain at the start of the cycle. If it doesn't, request service.

Samsung recommends cleaning the pump filter at least once a month or about every 40 washes, whichever comes first. The same drain-hose logic applies in the kitchen; see our [dishwasher not draining guide](https://applianceinsider.org/blog/dishwasher-not-draining/).

## UE, Ub, U6 and Ur: unbalanced load

**Ur** isn't a problem. It means the washer is about to add water, rebalance the load, and try the spin again, which makes the cycle run longer. **UE**, **Ub** and **U6** mean the washer gave up and won't finish the cycle because the load is unbalanced.

To fix it, untangle and rearrange the laundry so it's spread evenly in the tub, close the door, and press Start. If you keep getting unbalanced codes with normal loads, check that the washer is level, and see Samsung's washer-won't-spin guide for your model.

## dC, dE and dS: door errors

These codes mean the washer can't detect the door as closed and locked. Check that the latch is secure, that no laundry is caught in the door, and that the door is closed properly. If the latch or door is damaged, or the code won't clear, request service.

Two notes from Samsung:

- A door code can appear even when no cycle is running if Child Lock is on and there's water in the tub. If you don't close the door or turn Child Lock off within 30 seconds, the washer drains the water.
- On FlexWash washers, **1dC4** appears if the rubber button next to the upper washer's latch is missing. Replacing the button fixes it, and no service is needed.

Remember that on some models **dC** means an unbalanced load, not a door problem. Your manual will tell you which.

## LC, LE and 1E: leak or water level error

This code means the washer detected moisture where it doesn't belong, or there's a problem with the water level sensor itself. Samsung's steps:

1. Look for a leak. Some are small enough to go unnoticed, and fixing the leak clears the code.
2. Check that the supply hoses and drain hose behind the washer aren't kinked.
3. Run an empty cycle with no detergent or fabric softener and watch for suds. If suds appear, too much detergent or a non-HE detergent was used. Keep running empty cycles until no suds appear, then see if the code returns.

If no suds appear and the code continues, request service.

## Blinking lights on Samsung washers without a display

Samsung models without a digital display show errors as combinations of blinking lights. Samsung's examples include **Hot and Cold** (or Hot and Eco Warm) for a motor error, **Warm** for a communication error, **Hot and Tap Cold** (or Hot and Cool) for a MEMS sensor error, and **Hot and Medium** (or Hot and Mid) for a heater error. Because lights also blink in normal use, Samsung says to treat them as an error only if the washer isn't working normally, such as stopping mid-cycle. Power-cycle it, and request service if the pattern returns.

A blinking **Self Clean** light isn't an error. It's a reminder that appears after 20 washes on top-load models and 40 washes on front-load models.

## Codes that need a technician

Codes from the no-DIY-fix table above, any code that keeps returning after the checks, and a missing drain hose holder all need service. Don't open the cabinet to chase them; a qualified technician can test the part behind the code. Our [appliance repair cost guide](https://applianceinsider.org/appliance-repair-cost/) explains what to expect.

## How to prevent Samsung washer error codes

- **Use HE detergent, and not too much of it.** Excess or non-HE detergent causes SUd codes and can trigger LC leak codes.
- **Clean the pump filter monthly** (or every 40 washes) on front-load models.
- **Run Self Clean or Pure Cycle monthly.** Samsung says it needs no added cleaner. On models without Self Clean, Samsung says any washing machine cleaner will do; follow the cleaner's directions. Our [front-load washer smell guide](https://applianceinsider.org/blog/front-load-washer-smells-how-to-fix/) covers the gasket and dispenser too.
- **Keep the hoses right:** hot to hot, cold to cold, no kinks, valves fully open, and the drain hose 6 to 8 inches into the standpipe.
- **Keep the washer level** and spread loads evenly to avoid UE and Ub.
- **Give it its own circuit**, with no extension cord, to avoid voltage codes.

For other brands, see our [LG washer error codes guide](https://applianceinsider.org/blog/lg-washer-error-codes/), the [Whirlpool front-load washer error codes guide](https://applianceinsider.org/blog/whirlpool-front-load-washer-error-codes/), and the full [error code library](https://applianceinsider.org/error-codes/). Add the monthly washer tasks to your [maintenance calendar](https://applianceinsider.org/maintenance-calendar/).

## Step-by-step summary

Estimated time: 45m

Tools: Shallow pan or oil drain pan, Towels, Soft-bristle brush or old toothbrush, Needle-nose pliers

1. **Write down the exact code.** Note the code exactly as the display shows it, or which lights are blinking on models without a display, and find your model number in the owner's manual.
2. **Look up the code.** Match it to the table in this guide and to your manual, because some Samsung codes, such as dC, 3E and BE2, mean different things on different models.
3. **Do the safe checks for that code.** Depending on the code, open the water valves fully, fix swapped or kinked hoses, check the drain hose depth, clean the pump filter on front loaders, rearrange the load, or close the door firmly.
4. **Power-cycle the washer.** Unplug the washer or switch off its breaker for 1 minute for fill errors, or 2 to 3 minutes for other codes, then restore power and restart the cycle.
5. **Request service if it comes back.** If the code returns after the checks, or it is a code Samsung lists without a DIY fix (motor, communication, sensor, heater or system errors), request service.

## Products mentioned

(Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases. Some links on this site are affiliate links. If you buy through them, we may earn a commission at no extra cost to you. This never changes what we recommend.)

- Affresh Washing Machine Cleaner Tablets, 6 count: A washing machine cleaner for Samsung washers that don't have a Self Clean or Pure Cycle; Samsung says any washer cleaner will do on those models. (Samsung says its Self Clean cycle needs no added cleaner. Follow the cleaner's directions and your Samsung manual.)

## Frequently asked questions

**Q: How do I reset a Samsung washer error code?**

A: Samsung's basic reset is to power the washer off for 2 to 3 minutes, power it back on, and restart the cycle. For not-filling codes such as 4C, Samsung says to unplug the washer or switch off its breaker for 1 minute. If the code returns, fix the cause or request service.

**Q: What does 4C mean on a Samsung washer?**

A: 4C (also shown as 4E or nF) means water isn't entering the washer correctly. Check that both water valves are fully open, the hot and cold hoses go to the matching inlets and aren't kinked, and the inlet filters aren't clogged with debris.

**Q: What does 5C mean on a Samsung washer?**

A: 5C (also 5E, SE or nd) is Samsung's no-drain error. Samsung says an incorrectly installed drain hose is the most common cause, so check the hose depth, height and kinks first, then clean the pump filter on front-load models.

**Q: What is the difference between Ur and UE on a Samsung washer?**

A: Ur means the washer is retrying: it adds water, rebalances the load and tries to spin again, so no action is needed. UE, Ub and U6 mean it couldn't finish the cycle because the load is unbalanced, so untangle and rearrange the laundry and restart.

**Q: Is dC a door error or an unbalanced load on a Samsung washer?**

A: It depends on the model. Samsung says dC is a door error on some washers and an unbalanced load error on others, so check your owner's manual before deciding what to fix.

**Q: Why does my Samsung washer say SUd?**

A: SUd (also 5UD or Sd) means the washer detected too many suds and paused to let them settle. Samsung says it doesn't mean service is needed; it is caused by using too much detergent or a non-HE detergent.

## When to call a pro

For repairs beyond basic checks in Maryland, Virginia, Washington D.C., West Virginia, Pennsylvania, Delaware, North Carolina, South Carolina, and Georgia, Appliance Insider recommends [VIA Appliance](https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-samsung-washer-error-codes) (book online: https://viaappliance.com/?utm_source=applianceinsider&utm_medium=referral&utm_campaign=call-a-pro&utm_content=post-samsung-washer-error-codes#book). VIA Appliance is a featured repair partner of Appliance Insider.

## Sources

- [Samsung US Support: Samsung washing machine information and error codes](https://www.samsung.com/us/support/troubleshoot/TSG10000997/)
- [Samsung US Support: Samsung washing machine will not drain](https://www.samsung.com/us/support/troubleshoot/TSG10007110/)
- [Samsung US Support: How to clean your Samsung washer](https://www.samsung.com/us/support/answer/ANS10003197/)
