# Whirlpool Front-Load Washer Error Codes: What They Mean and How to Fix Them

> Plain-English guide to Whirlpool front-load washer codes, including F5 E2, F8 E1, F9 E1, F7 E1, Sud, and Int, and what to check before calling for service.

- URL: https://applianceinsider.org/blog/whirlpool-front-load-washer-error-codes/
- Publisher: Appliance Insider (https://applianceinsider.org)
- Category: Troubleshooting & Error Codes; Appliance: Washers; Brands: Whirlpool
- Published: 2026-10-01; Last updated: 2026-10-01; Author: Appliance Insider Editorial Team

Whirlpool front-load washers display short codes when something interrupts a cycle. Many of them point to something you can fix in a few minutes, like a kinked hose or the wrong detergent. This guide explains the most common codes based on Whirlpool's own product-help documentation.

> **Important:** Codes vary by model and generation. Whirlpool notes its list is not every code for every washer, so confirm with the owner's manual for your model number (usually on a label inside the door rim).

## How to clear a code

On many Whirlpool front-load washers:

1. Press **Pause/Cancel twice**, then **Power once**.
2. If the code is still there, unplug the washer (or turn off the breaker) for **5 minutes**, reconnect, and restart the cycle.

If a code keeps coming back after the checks below, there is an underlying fault to diagnose.

## Common Whirlpool front-load washer codes

| Code | What it means | What to check |
| --- | --- | --- |
| **F5 E2** | Door is not locking properly | Remove anything caught in the door or gasket, close the door firmly, then clear the code. |
| **F7 E1** | Motor can't reach the right speed | Confirm all shipping bolts were removed after installation and the washer isn't overloaded, then clear the code. |
| **F8 E1** or **LO FL** | Low water flow | Make sure both hot and cold supply valves are fully open, fill hoses aren't kinked, and no flood-stop devices are restricting flow. |
| **F8 E2** | Dispenser system problem (select models) | Check that the detergent drawer or bulk-detergent cartridge isn't clogged with detergent; clean the dispenser. |
| **F9 E1** | Draining is taking too long (typically over 8 minutes) | Check the drain hose for kinks or clogs, use the U-shaped hose form, and confirm the standpipe is between 39 and 96 inches high. Excess suds can also slow draining. |
| **Sud** or **Sd** | Too many suds | Use HE detergent in the right amount; avoid "no-splash" thickened bleach; check for a restricted drain. The washer adds rinses automatically. |
| **Int** | Cycle was paused or canceled | Normal. The washer may take 20 to 30 minutes to stop and drain. Clear with Pause/Cancel twice, Power once. |
| **LOC** or **LC** | Control lock is on | Press (or press and hold) the Control Lock button per your manual. |
| **dET** | Detergent cartridge not detected (select models) | Seat the bulk detergent cartridge and close the drawer; ignore if you use single-dose packs. |
| **rL** or **F34** | Items detected during Clean Washer cycle | Empty the drum and restart the Clean Washer cycle. |
| **Other F# E#** | Other fault | Disconnect power for 5 minutes and restart. If it returns, schedule service. |

## The codes homeowners see most

### F9 E1: long drain

This is the most common drain-related code. Start with the easy causes:

- **Drain hose:** kinks behind the washer are common after it is pushed back into place. Straighten the hose and use the U-shaped hose form that came with the washer.
- **Standpipe height:** Whirlpool specifies a standpipe height between **39 inches minimum and 96 inches maximum**.
- **Suds:** too much detergent, or non-HE detergent, slows draining.
- **Drain pump filter:** many front-loaders have a coin-trap or pump filter behind a small access panel at the lower front. Check your manual; put down towels and a shallow pan first, because water will come out.

If the hose and filter are clear and the code persists, the drain pump may be failing.

### F8 E1 / LO FL: low water flow

Usually a water supply issue: a valve that was turned off (or only partially opened), a kinked fill hose, or a clogged inlet screen. Front-load washers use relatively little water, so even a partially closed valve can trigger this code.

### F5 E2: door lock

Check for clothing or a bunched-up gasket preventing the door from closing. If the door closes cleanly and the code keeps appearing, the door lock assembly or its wiring may need to be tested.

### Sud: too many suds

Front-load washers need **HE (high-efficiency) detergent**, and only the amount the label recommends for your load and water hardness. The washer pauses and rinses to break down suds, which makes cycles longer. If you are using HE detergent correctly and still see Sud, check for a restricted drain.

## Prevent repeat codes

- Use HE detergent, measured, not eyeballed.
- Run the **Clean Washer** cycle monthly with a washer cleaner, and wipe the door gasket folds dry.
- Leave the door ajar after use so the drum can dry.
- Check the drain pump filter every few months if your model has one.

See the full [appliance maintenance calendar](https://applianceinsider.org/maintenance-calendar/) for other monthly and annual tasks.

## Step-by-step summary

Estimated time: 30m

Tools: Towels and a shallow pan, Flashlight

Supplies: HE detergent

1. **Write down the exact code.** Note the full code, such as F9 E1, and what the washer was doing when it appeared.
2. **Look up the code.** Match it to the table in this guide and to your owner's manual, since codes vary by model.
3. **Do the safe checks.** Check the door, water supply valves and fill hoses, drain hose and standpipe, load size, and detergent type, depending on the code.
4. **Clear the code.** On many Whirlpool front-load washers, press Pause/Cancel twice and then Power once.
5. **Reset power if needed.** For a code that will not clear, unplug the washer (or switch off its breaker) for 5 minutes, then restart the cycle.
6. **Schedule service if it returns.** If the same code comes back after these checks, have a technician diagnose the washer.

## Products mentioned

(Affiliate disclosure: Appliance Insider may earn a commission from Amazon links.)

- Affresh Washing Machine Cleaner Tablets, 6 count: Monthly cleaning tablet for front-load and top-load washers; use with the Clean Washer cycle to cut residue and odor.

## Frequently asked questions

**Q: How do I clear an error code on a Whirlpool front-load washer?**

A: Whirlpool's instructions for many front-load models are to press Pause/Cancel twice and then Power once. If the code remains, unplug the washer or disconnect power for 5 minutes, then reconnect it and restart the cycle.

**Q: What does F9 E1 mean on a Whirlpool washer?**

A: F9 E1 means draining is taking longer than expected (Whirlpool says typically over eight minutes). Check for a kinked or clogged drain hose, confirm the standpipe height, and make sure you are using HE detergent.

**Q: What does Sud or Sd mean on a Whirlpool washer?**

A: It means the washer detected too many suds. The washer will pause and add rinses automatically to break them down. Use HE detergent in the correct amount, avoid thickened no-splash bleach, and check that the drain hose is not restricted.

**Q: Why does my Whirlpool washer say F5 E2?**

A: F5 E2 means the door is not locking properly. Make sure nothing (often a sock or the gasket) is caught in the door, close it firmly, and clear the code. If it keeps returning, the door lock or latch may need service.

**Q: Do these codes apply to Whirlpool top-load washers?**

A: No. Top-load and front-load washers use different code lists. This guide covers front-load models; check your owner's manual for top-load codes.

## When to call a pro

For repairs beyond basic checks in Maryland, Virginia, Washington D.C., West Virginia, Pennsylvania, Delaware, North Carolina, South Carolina, and Georgia, Appliance Insider recommends VIA Appliance (https://viaappliance.com). VIA Appliance is a featured repair partner of Appliance Insider.

## Sources

- [Whirlpool Product Help: Error Codes in Front Load Washers](https://producthelp.whirlpool.com/Laundry/Washers/Product_Info/Washer_Product_Assistance/Error_Codes_in_Front_Load_Washers)