Troubleshooting & Error Codes Ranges & Ovens
LG Oven Error Codes: What F1, F9, F10, F11 and PF Mean on LG Ranges, and LG's Reset Before Thanksgiving
LG oven error codes from LG's own support pages: what F1, F9, F10, F11, PF and the cooktop codes mean, LG's reset steps, and when to call for service.
LG oven error codes mostly fall into a few groups: F1, F2, F4 and F5 are oven temperature sensor (thermistor) errors, F9 means the oven isn’t heating properly, F10 is a door lock failure and F11 is a communication error inside the range. PF only means the power was interrupted. For nearly all of them, LG’s fix is the same: press CLEAR/OFF and try again, then switch the breaker off for 30 seconds, and request service if the code comes back.
This guide covers the codes on LG USA Support’s range error code list, what each one means and what LG says to do. It’s worth a look before Thanksgiving, when the oven runs for hours, the meat probe goes in and a self-clean cycle can end with a locked door at the worst time.
How to clear an LG oven error code
LG’s reset steps for most F codes:
- Press CLEAR/OFF and try the original function again (on radiant cooktop models, press Power ON/OFF).
- If the code reappears, switch the range’s circuit breaker off, wait 30 seconds, and switch it back on.
- If the code keeps coming back, or you can’t do these steps, LG says the range needs service.
For a few codes, including F3, F21 to F25, F27 and the induction, griddle and sous vide codes, LG skips step 1 and goes straight to the breaker reset. A reset only clears the message. If a part has failed, the code will come back.
LG oven error code table
| Code | What LG says it means | What to do |
|---|---|---|
| F1, F2 | Upper oven thermistor (temperature sensor) error | CLEAR/OFF, then 30-second breaker reset, then service |
| F3 | Touch pad sensor key error | 30-second breaker reset, then service |
| F4, F5 | Lower oven thermistor error | CLEAR/OFF, then breaker reset, then service |
| F6 | Upper oven heating error | CLEAR/OFF, then breaker reset, then service |
| F7 | Upper convection fan error | CLEAR/OFF, then breaker reset, then service |
| F8 | Oven meat probe error | CLEAR/OFF, then breaker reset, then service |
| F9 | Upper oven is not heating properly | CLEAR/OFF, then breaker reset; check the gas valve on gas models; then service |
| F10 | Door locking system failure (upper oven) | CLEAR/OFF, then breaker reset, then service |
| F11 | Communication error | CLEAR/OFF, then breaker reset, then service |
| F16 | Oven sensor issue | CLEAR/OFF, then breaker reset, then service |
| F17 | Convection fan error | CLEAR/OFF, then breaker reset, then service |
| F18 | Oven meat probe error | CLEAR/OFF, then breaker reset, then service |
| F19 | Oven heating error | CLEAR/OFF, then breaker reset, then service |
| F20 | Door locking system failure (lower oven) | CLEAR/OFF, then breaker reset, then service |
| F21, F22, F24, F25 | Steam sensor failure | Breaker reset, then service |
| F27 | Cooling fan stalled or locked during self-clean | Breaker reset, then service |
| F33, F34 | Front induction burner temperature sensor error | Breaker reset, then service |
| F36 | Transistor error | Breaker reset, then service |
| F38 | Communication error between the main board and inverter | Breaker reset, then service |
| F42 | Voltage error | Breaker reset, then service |
| F45, F46 | Fan error | Breaker reset, then service |
| F51, F52, F56, F59 | Griddle sensor error, sensor short, heating error, or griddle not heating properly | Breaker reset, then service |
| F62, F69 | Sous vide temperature sensor error, or sous vide not heating properly | Breaker reset, then service |
| PF | Power to the range was interrupted | Press CLEAR/OFF and set the function again |
| HS (H5) | Cooktop is hotter than 150°F; not an error | Let it cool; if the surface is cool and it stays on, breaker reset |
| Sb (5b) | Sabbath mode is on; not an error | Turn Sabbath mode off (steps below) |
F9: LG oven not heating properly
LG’s list says F9 means the upper oven isn’t heating properly. LG Canada’s help page is more specific: on an electric range, F9 shows when the oven fails to get above 150°F after 5 minutes of preheating. It lists the likely causes as a shorted element, a defective relay circuit board or a defective relay connector, which are all service jobs.
What you can safely check first:
- Press CLEAR/OFF to stop the beeping, then try to preheat again. LG notes that a new temperature is canceled if you don’t press START within 25 seconds.
- Do the 30-second breaker reset. LG Canada suggests leaving electric models without power for 3 to 5 minutes, and gas models for five minutes.
- On a gas range, LG says to check the main gas shut-off valve or the oven’s gas shut-off valve. If the range was pulled out for cleaning, the gas may have been turned off. LG also says a gas range needs its own 15 to 20 amp, 120-volt circuit and must not be plugged into an extension cord.
- If F9 returns, request service. Don’t try to replace the element or test the relay board yourself.
If your oven won’t heat but shows no code, see our guides to an electric oven not heating and a gas oven not heating while the burners work.
F10 and F20: door lock failure (and a door locked after self-clean)
F10 is a door locking system failure in the upper oven, and F20 is the same fault in the lower oven of a double-oven model. Press CLEAR/OFF, try the breaker reset, and request service if the code returns.
A locked door with no code is usually normal. LG says the door stays locked after a Self Clean or EasyClean cycle until the oven has cooled to a safe temperature, and the lock releases on its own. If the oven is cool and the door is still locked:
- Press and hold CLEAR/OFF for more than three seconds. LG notes this step varies by model, so check your manual.
- Unplug the range or switch off its breaker for 5 minutes, then restore power. You should hear the lock disengage.
- If the door stays locked, request service.
LG also says not to force the door while the lock icon is on, and to cancel a self-clean cycle with CLEAR/OFF if there’s excessive smoke or fire in the oven. F27, a cooling fan problem during self-clean, is one more reason not to run that cycle days before a holiday.
F1, F2, F4, F5, F16 and F11: sensor and communication errors
F1 and F2 are upper oven thermistor (temperature sensor) errors, F4 and F5 are the lower oven’s, and F16 is an oven sensor issue. F11 is a communication error inside the range, and F38 is one between the main board and the inverter on induction models. A power blip can trigger these, so LG’s reset steps are worth trying. If the code returns, the sensor, wiring or board needs a technician.
F8 and F18: meat probe errors
On LG models with a built-in meat probe, F8 and F18 are probe errors. Press CLEAR/OFF and try again, and check your manual for how the probe should be plugged in. If the code keeps returning, request service. Until it’s fixed, a separate thermometer works fine for the turkey; see our meat thermometer guide for the doneness temperatures.
LG radiant cooktop error codes
LG’s radiant cooktop models show errors as lit segments on the touch slider rather than as letters. LG numbers them Error Code 1 through 6:
| Lit segments | What LG says it means | What to do |
|---|---|---|
| 1, 2 or 3 | Thermistor error | Press Power ON/OFF, then breaker reset, then service |
| 4 | Metal objects or water have been on the touch pads too long | Clean the cooktop and clear anything off the touch pads, then reset |
| 5 | Display error | Press Power ON/OFF, then breaker reset, then service |
| 6 | Low voltage | Have a qualified electrician check it |
Code 4 is common on a crowded holiday cooktop: a spoon, lid or puddle of water left on the controls is enough to trigger it.
PF, HS and Sb: messages that aren’t faults
- PF means the power was interrupted. Press CLEAR/OFF and set the oven again. It often shows after an outage or a tripped breaker.
- HS (it can look like H5) means a cooktop surface is hotter than 150°F. LG says it isn’t an error. If the surface is at room temperature and the indicator stays on, do the breaker reset.
- Sb (it can look like 5b) means Sabbath mode is on. While it’s on, you can’t change the temperature, and the timer, light and alarm are disabled. LG’s steps to turn it off are: press Bake, set the temperature with the +/- keys, press Start, then press and hold Clock for 3 seconds. Check your manual if your model’s keys differ.
Before Thanksgiving: test the oven now
The best time to find a code is several days before the holiday, not on Thursday morning.
- Run a test preheat to 350°F and use the oven for a normal meal. If it throws an F code, you still have time for a service visit.
- Don’t self-clean right before the holiday. Because the door stays locked until the oven cools, and F10 and F27 are self-clean-related faults, run any self-clean cycle weeks ahead. Our oven cleaning guide covers lower-risk options.
- Adjust the temperature only if there’s a pattern. LG says to use a new oven for a few weeks before changing the setting. On models with the feature (shown as AdJU on some LG ranges), start with a 15°F change. LG allows up to 35°F either way, and the adjustment doesn’t affect broil or self-clean. Your owner’s manual has the exact key steps for your model.
- Keep the cooktop controls clear of pans, utensils and spills to avoid touch pad codes.
For other brands, see our Samsung oven error codes and GE and Whirlpool oven error codes guides, or browse the error code hub. Our maintenance calendar covers routine range care through the year.
When an LG oven code needs a technician
Request service if:
- the same F code comes back after CLEAR/OFF and a 30-second breaker reset;
- F9 persists on a gas range with the gas valve open, or on an electric range after a full power reset;
- the door stays locked after the oven has cooled and the CLEAR/OFF and 5-minute power steps didn’t release it;
- the radiant cooktop shows the low-voltage code (6 segments) or F42 keeps returning, which calls for an electrician to check the supply;
- you smell gas, see scorching or hear arcing. Turn the range off and don’t use it until it’s inspected; for gas, leave the house and call your gas utility from outside.
Step-by-step summary
- Write down the exact code. Note the code exactly as the display shows it, such as F9 or PF, and find it in the table. Codes vary by model, so check your owner's manual too.
- Rule out messages that aren't faults. HS or H5 means the cooktop is still hotter than 150°F, Sb or 5b means Sabbath mode is on, and PF means the power was interrupted. Let the cooktop cool, turn off Sabbath mode, or press CLEAR/OFF and set the oven again.
- Press CLEAR/OFF and try again. For most F codes, LG says to press CLEAR/OFF and try the original function again. On radiant cooktop models, press the Power ON/OFF button instead.
- Reset the circuit breaker for 30 seconds. If the code comes back, switch the range's circuit breaker off, wait 30 seconds, and switch it back on.
- Check the basics behind oven-not-heating codes. For F9 on a gas range, make sure the gas shut-off valve is open, especially if the range was recently moved. On any model, confirm you pressed START within 25 seconds of setting the temperature.
- Request service if it returns. If the same code returns after the breaker reset, LG says the range needs service. Don't keep resetting it or open the range yourself.
Frequently asked questions
How do I reset an LG oven error code?
LG's reset for most codes is to press CLEAR/OFF and try the original function again. If the code returns, switch off the range's circuit breaker, wait 30 seconds, and switch it back on. If it still comes back, LG says the unit needs service.
What does F9 mean on an LG oven?
LG's error code list says F9 means the upper oven is not heating properly. LG Canada's help page adds that on electric ranges F9 appears when the oven fails to get above 150°F after 5 minutes of preheating, and that a persistent F9 needs a service technician.
What does F10 mean on an LG oven?
F10 means a door locking system failure in the upper oven, and F20 is the same fault in the lower oven of a double-oven range. Press CLEAR/OFF, then try a 30-second breaker reset; if it returns, LG says to request service. Never force a locked oven door open.
What does PF mean on an LG range?
PF means power to the range was interrupted, such as after an outage or a tripped breaker. Press CLEAR/OFF and set the function again. If PF keeps coming back, try a 30-second breaker reset and then request service.
Why is my LG oven door still locked after self-clean?
LG ranges keep the door locked after Self Clean or EasyClean until the oven has cooled to a safe temperature. If it's cool and still locked, LG says to press and hold CLEAR/OFF for more than three seconds, then try cutting power for 5 minutes, and request service if it stays locked.
What does Sb mean on an LG oven?
Sb (it can look like 5b) means the range is in Sabbath mode, which is not an error. While it's on, you can't change the temperature, and the timer, light and alarm are disabled. LG's steps to turn it off are on its error code page and in your owner's manual.
Sources
- LG USA Support: LG Range - Error Codes List (updated Apr. 20, 2026)
- LG Canada Support: Electric Range and Gas Range F-9 error code
- LG USA Support: LG Range - Troubleshooting A Locked Oven
- LG USA Support: LG Range - How to Clean Your Oven Using Self Clean
- LG USA Support: Oven Not Heating - Gas Ranges
- LG Canada Support: Basic Settings Adjustments [Range] (oven temperature adjustment)