Troubleshooting & Error Codes Dryers

Whirlpool Dryer Error Codes: What AF, F4E3, PF, L2, F3E1 and Other F#E# Codes Mean

Whirlpool dryer error codes explained from Whirlpool's own help pages: what AF, F4E3, PF, L2, ERR, Loc and F#E# codes mean and what to try before service.

A white dryer in a bright laundry room with its lint screen resting on top and a basket of folded flannel sheets beside it

Whirlpool dryer error codes point to one of a few problems, and the most common one, AF (also shown as F4E3 or a “Check Vent” light), means the lint screen or exhaust vent is restricted, not that the dryer is broken. According to Whirlpool, PF means a power failure interrupted the cycle, L2 (or F4E4) means low or no line voltage is keeping the heater off, and any code that alternates between an F number and an E number (such as F3E1) means the control found a problem that needs service. Most codes start with the same fix: clean the lint path or check power, then reset the dryer at the breaker.

Codes and the way they appear vary by model, so use this as a guide and confirm in your owner’s manual. Some codes only exist on certain dryers; the Check Vent light, for example, works only during Automatic cycles on models that have it.

How to reset a Whirlpool dryer error code

Whirlpool lists the same power cycle for most codes:

  1. Turn off the circuit breaker (or breakers) for the dryer. Whirlpool says 1 minute for most F#E# codes, L2, ERR and dashes in the display, and 5 minutes for E1, E2, E3, F1E1, F3E4, 0E, 0g, 3E and 6E.
  2. Turn the breaker back on.
  3. Start a timed dry cycle.
  4. Watch the dryer for 1 minute to make sure the code doesn’t come back.

Several codes clear without a breaker reset. Touch any key to clear AF, F4E3, L2 and F4E4 from the display (the dryer keeps running while they show). Press Power to clear F3E2 and F3E5. If a code returns right after a reset, the cause is still there; use the table to see what to check next.

Whirlpool dryer error code list

CodeWhat Whirlpool says it meansWhat to check
AF, Check VentRestricted airflow: lint screen or vent clogged, or vent crushed, kinked or with too many turnsLint screen, vent behind the dryer, outside exhaust hood
F4E3Restricted airflow (same as AF)Same as AF
PFPower failure interrupted the cycleHold Start to resume, or press Power to clear
L2Low or no line voltage; heater won’t turn onBoth breakers or fuses, power cord installation; electrician
F4E4Low or no line voltage (same checks as L2)Same as L2
ERRDoor not completely closed and latchedPush the door shut; some models have two latches
LocControl Lock is onHold the Control Lock key for 3 seconds
F3E2, F3E5Five loads in a row dried without moisture sensor dataLevel the dryer, dry larger loads, use an Automatic cycle
F3E1Exhaust thermistor1-minute breaker reset; service if it returns
F3E3Inlet thermistor1-minute breaker reset; service if it returns
F4E1Heater system: heater or heater relays1-minute breaker reset; service if it returns
F1E3, F1E5Control unit or its wiringTouch Power, select a cycle, hold Start/Pause; if that fails, unplug the dryer
F1E4Control unit or its wiring1-minute breaker reset; service if it returns
F2E1Keypad1-minute breaker reset; service if it returns
F2E2Keypad or control1-minute breaker reset; service if it returns
F2E4User interface or its wiringTouch Power, select a cycle, hold Start/Pause; if that fails, unplug the dryer
F2E5User interface or its wiring1-minute breaker reset; service if it returns
F6E1Communication error: main control board, touchpad or wiring1-minute breaker reset; service if it returns
F7E1Motor system: motor, control or wiring1-minute breaker reset; service if it returns
F6E2, F6E3, F9E2, FCE1, dashesNo meaning published; power cycle listed1-minute breaker reset; service if it returns
E1, E2, E3, F1E1, F3E4, 0E, 0g, 3E, 6ENo meaning published; power cycle listed5-minute breaker reset; service if it returns

Whirlpool’s own help pages give a meaning for some codes but list only the reset steps for others. Where it doesn’t publish a meaning, we haven’t guessed one. Check your owner’s manual or the tech sheet for your model.

What AF, F4E3 and Check Vent mean on a Whirlpool dryer

Whirlpool says AF and F4E3 both mean restricted airflow: the lint screen or vent is clogged, or the vent is crushed, kinked or has too many turns. The dryer keeps running while the code shows, and touching any key clears it, but the clothes will take longer to dry until you fix the airflow. On models with a Check Vent light, the dryer checks airflow at the start of Automatic cycles; the light stays on for the cycle and clears when the cycle ends, when you touch Power or when you open the door. It keeps coming back until the cause is fixed.

Whirlpool’s checks, in order:

  1. Clean the lint screen.
  2. Check that the vent between the dryer and the wall isn’t crushed or kinked.
  3. Make sure that section of vent is free of lint and debris.
  4. Make sure the outside exhaust hood is free of lint and debris.
  5. Confirm the vent run is within the maximum length and number of elbows the installation instructions allow for your vent type.
  6. Select a Timed Dry heated cycle and restart the dryer. If the code persists, Whirlpool says to have the entire home vent run cleaned by a venting specialist.

A quick test from Whirlpool: run the dryer for 5 to 10 minutes and hold your hand under the outside exhaust hood. If the air coming out is weaker than a hair dryer on high, clean lint out of the whole vent system and the hood. Whirlpool says the vent run should be cleaned every one to two years, or sooner if drying slows down, and it sells a dryer vent test kit (part W11224254) that shows whether the vent is restricted.

Cleaning the vent run with a LintEater RLE202 kit

If the vent is lint-filled rather than crushed, a rotary brush kit such as the Gardus LintEater RLE202 can clean a standard 4-inch duct from the dryer end or the outside hood. Our dryer vent cleaning guide walks through the whole job. Replace crushed or kinked flexible duct instead of cleaning it, and call a vent cleaning service for long runs, roof exits or anything you can’t reach safely.

What L2 and F4E4 mean on a Whirlpool dryer

Both codes mean low or no line voltage. There may be a problem with your home’s power supply that keeps the heater from turning on, so the drum turns but the clothes don’t get hot. The dryer keeps running, and touching any pad clears the code. Whirlpool notes that L2 shows only during initial installation.

What to check:

  1. Both breakers. Whirlpool says electric dryers need a separate 30-amp circuit fused on both sides of the line, so there are two breakers (or fuses): one runs the motor and the other runs the heating element. If only one has tripped, the drum can turn without heat. Reset a tripped breaker or replace a blown fuse.
  2. The power supply and cord. Electric dryers need a 240-volt supply. Whirlpool says to make sure the power cord is installed per the installation instructions and the terminal screws at the dryer are tight, and to unplug the dryer before checking those screws.
  3. Restart. Select a Timed Dry heated cycle and restart the dryer. If the message persists, Whirlpool says to consult a qualified electrician.

What PF means on a Whirlpool dryer

PF means a power failure interrupted the drying cycle. Touch and hold Start to restart the cycle, or press Power to clear the display.

Whirlpool adds two less obvious causes. During an outage, electrical “noise” on the supply line can register as the wrong voltage and trigger PF. Pressing keys before the control’s 10-second delay after power comes back can also cause it. If you’ve had a recent outage, turn off the dryer’s breaker for 1 minute, turn it back on, watch the dryer for 1 minute and confirm it runs normally.

What F3E1 and other F#E# codes mean

Whirlpool says a code that alternates between F# and E# means the dryer’s control has detected a problem that requires service. Its help pages name the system for several of them: F3E1 is the exhaust thermistor, F3E3 the inlet thermistor, F4E1 the heater or heater relays, F6E1 communication between the main control and the touchpad, and F7E1 the motor system.

Whirlpool’s first step for F3E1 and most other F#E# codes is the 1-minute breaker reset described above. For F1E3, F1E5 and F2E4, it says to touch Power, select a cycle and hold Start/Pause first, then unplug the dryer if that doesn’t work. If any F#E# code comes back, schedule service. Testing thermistors, heaters or control boards means opening the cabinet near live wiring, so leave that to a technician.

F3E2 and F3E5: moisture sensor

These two are different from other F#E# codes because you can often fix the cause yourself. Whirlpool says they appear when five loads in a row dry without the moisture sensor registering any data. Press Power to clear the code, then:

  • Level the dryer. A dryer that isn’t level can keep clothes from touching the moisture sensors. Measure from the cabinet edge, because the top may be curved, and adjust the feet.
  • Dry bigger loads. Very small loads or single items may never touch the sensors. Dry larger loads, or use an Automatic cycle instead of Timed Dry.
  • Power cycle if the code keeps returning, then call for service.

ERR and Loc: the two codes that aren’t faults

  • ERR means the door isn’t completely closed and latched, and the dryer won’t run until it is. The door can look shut without latching. Push it firmly; some models have an upper and a lower latch, and both must catch. If ERR stays, do the 1-minute breaker reset.
  • Loc means the Control Lock is on, and the dryer won’t start or run. Press and hold the Control Lock key for 3 seconds until the display counts down 3-2-1. On some models it shares a button with another option, such as Steam; hold the button itself, not the label under it.

How to keep Whirlpool dryer codes from coming back

Most of the codes you can fix yourself come down to airflow and power:

  • Clean the lint screen before every load.
  • Keep the vent behind the dryer short, straight and uncrushed when you push the dryer back.
  • Have the full vent run cleaned every one to two years, as Whirlpool recommends; our maintenance calendar lists when.
  • After a power outage, wait a few seconds before you press any buttons.

If your dryer is a Whirlpool washer-and-dryer pair, our Whirlpool front-load washer error codes guide covers the washer side, and you can find every brand we cover on the error code hub.

Step-by-step summary

Time
About 30 min
Tools
Level
Supplies
Soft brush
  1. Write down the exact code. Note the code exactly as the display shows it. F#E# codes alternate between two parts, such as F3 and E1, so watch the display long enough to read both.
  2. Try the simple fixes for ERR, Loc and PF. Push the door until it latches for ERR, hold the Control Lock key for 3 seconds for Loc, and touch and hold Start to resume after a PF power failure.
  3. Clean the lint screen and check the vent for AF or F4E3. Clean the lint screen, make sure the vent behind the dryer isn't crushed or kinked, and confirm the outside exhaust hood is free of lint, then run a Timed Dry heated cycle.
  4. Check both breakers for L2 or F4E4. On an electric dryer, make sure neither of the two breakers or fuses for the dryer has tripped or blown, and have an electrician check the supply if the code returns.
  5. Power-cycle the dryer at the breaker. For F#E# codes and other codes, turn off the dryer's circuit breaker for the time Whirlpool lists (1 or 5 minutes), turn it back on, start a timed dry cycle and watch it for 1 minute.
  6. Schedule service if the code comes back. Whirlpool says an alternating F#E# code means the control found a problem that needs service. If the code returns after a power cycle, schedule service instead of opening the dryer.

Tools and supplies mentioned

Gardus LintEater RLE202 Rotary Dryer Vent Cleaning Kit

by Gardus

For AF, Check Vent and F4E3 codes caused by lint in the vent run. Four 3-foot screw-together flexible rods with a self-feeding auger brush, a lint trap brush, and vacuum and dryer adapters. Requires a cordless drill.

Fit check: Sized for standard 4-inch dryer ducts. Crushed or kinked foil duct should be replaced, not cleaned, and long runs may need a professional.

Check price on Amazon

Frequently asked questions

What does AF mean on a Whirlpool dryer?

Whirlpool says AF means restricted airflow: the lint screen or vent is clogged, or the vent is crushed, kinked or has too many turns. The dryer keeps running, and touching any key clears the code, but you need to clean the lint screen and vent to stop it coming back.

How do I reset a Whirlpool dryer error code?

Whirlpool's reset for most codes is to turn off the dryer's circuit breaker for 1 minute (5 minutes for some codes), turn it back on, start a timed dry cycle and watch for 1 minute. If the code returns, the dryer needs service.

What does PF mean on a Whirlpool dryer?

PF means a power failure interrupted the drying cycle. Touch and hold Start to restart the cycle, or press Power to clear the display; if it keeps appearing after an outage, turn off the dryer's breaker for 1 minute and turn it back on.

Why does my Whirlpool dryer show L2 and not heat?

Whirlpool says L2 means low or no line voltage, which keeps the heater from turning on while the drum still turns. Electric dryers use two breakers or fuses, so check that neither has tripped or blown, and call a qualified electrician if the code persists.

What does F3E1 mean on a Whirlpool dryer?

Whirlpool lists F3E1 as an exhaust thermistor code. Its first step is to turn off the dryer's breaker for 1 minute, turn it back on, start a timed dry cycle and watch for 1 minute; if F3E1 returns, schedule service.

What does Loc mean on a Whirlpool dryer?

Loc means the Control Lock is on, and the dryer won't start while it is locked. Press and hold the Control Lock key, which on some models shares a button with another option, for 3 seconds to unlock it.

Sources

Whirlpool dryer error codesWhirlpool dryerAFCheck VentF4E3PFL2F4E4F3E1F3E2ERRLocdryer not heating

Found an error? We correct mistakes promptly. See our corrections policy.